Manual

ManualsBrandsGW Instek ManualsInsulation TestersGPT-9801 Insulation tester, Dielectric withstand tester 100 V, 250 V, 500 V, 1000 V 9500 MΩ

Table Of Contents

Electrical Safety Tester

GPT-9000 Series

QUICK START GUIDE

GW INSTEK PART NO. 82PT-99040MA1

ISO-9001 CERTIFIED MANUFACTURER

Summary of content (20 pages)

PAGE 1
Electrical Safety Tester GPT-9000 Series QUICK START GUIDE GW INSTEK PART NO.
PAGE 2
This manual contains proprietary information, which is protected by copyright. All rights are reserved. No part of this manual may be photocopied, reproduced or translated to another language without prior written consent of Good Will company. The information in this manual was correct at the time of printing. However, Good Will continues to improve products and reserves the right to change specification, equipment, and maintenance procedures at any time without notice. Good Will Instrument Co., Ltd. No.
PAGE 3
Table of Contents Table of Contents INTRODUCTION ............................................................. 4 GPT-9000 Series Overview .......................................................................... 4 Series lineup ................................................................................................ 4 Panel Overview ............................................................................................ 5 Front Panel (GPT-9801/9802/9803) ........................................
PAGE 4
GPT-9000 Series Quick Start Guide INTRODUCTION This Quick Start Guide is intended as a fast introduction to operating the GPT-9000 Series Safety Testers. This Quick Start Guide assumes that the user is familiar with safety testers. For comprehensive instructions on the GPT-9000 Series, please see the User Manual, located on the accompanying CD. GPT-9000 Series Overview The GPT-9000 Series Safety Testers are AC/DC withstanding voltage, insulation resistance and ground bond safety testers.
PAGE 5
T-9804 INTRODUCTION Panel Overview Front Panel (GPT-9801/9802/9803) PASS/FAIL indicators Function keys Directional keys Display AC / DC Withstanding Voltage / Insulation Resistance GPT-9803 Tester PASS FAIL ESC PAGE READY READY indicator TEST CAUTION 5.0 kVAC MAX. HIGH VOLTAGE 6.0 kVDC MAX.
PAGE 6
GPT-9000 Series Quick Start Guide OPERATION Menu Tree This section describes the overall structure of the operation statuses and modes for the GPT-9000 safety testers. The testers have two main testing modes (MANU, AUTO) and 5 main operation statuses (VIEW, EDIT, READY, STOP and TEST).
PAGE 7
OPERATION VIEW Status Description VIEW status is used to select a manual test in the MANU mode or an automatic test/step in AUTO mode. VIEW status will display all the parameters of the current test. VIEW status is also used to put the tester into MANU or AUTO mode. AUTO number MANU number AUTO= 0 0 1 - 0 0 2 A U T O _ N AME MANU = * * * - 0 0 2 MA NU _ N AME FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA 0 100 A CW D CW kV RAMP I R mA =000 . 1S GB VIEW status RE F # = 0 0 .
PAGE 8
GPT-9000 Series Quick Start Guide Go to EDIT Status  Press the EDIT/SAVE key. EDIT/SAVE Go to READY Status  Press the STOP button when a MANU test or AUTO test has been selected. STOP AUTO/MANU Mode Description MANU mode is used to create and execute manual tests. AUTO mode is used to create automatic tests that execute up to 16 steps (manual tests) sequentially. AUTO mode AUTO= 0 0 1 - 0 0 2 MANU mode MANU = * * * - 0 0 2 MA NU _ N AME FREQ= 6 0 H z H I S E T = 0 1 .
PAGE 9
OPERATION EDIT Status Description MANU MODE EDIT status is accessed by pressing the EDIT/SAVE key when in VIEW status. EDIT status is used to edit the current manual test or the automatic test. Pressing the EDIT/SAVE key again will save any changes. Pressing the ESC key will cancel any changes. MANU number Reference I or Ω MANU test name ARC status Frequency Test voltage MANU = * * * - 0 0 2 MANU _ NAME FREQ= 6 0 H z H I S E T = 0 1 . 0 0mA 0 100 A CW Test function AUTO MODE RAMP I R mA =000 .
PAGE 10
GPT-9000 Series Quick Start Guide Set the Test Voltage/Current (MANU mode only)  Use the UP/DOWN arrow keys to bring the cursor to the Test voltage/Current.  Use the scroll wheel to set the voltage/current. Choose HI/LO SET limits (MANU mode only)  Press the HI/LO soft-key or use the UP/DOWN arrow keys to choose either HI or LO SET.  Use the scroll wheel to edit the setting. H I / LO OR Ramp Time (MANU mode only)  Use the UP/DOWN arrow keys to bring the cursor to Ramp time.
PAGE 11
OPERATION Reference (MANU mode only)  Use the UP/DOWN arrow keys to bring the cursor to REF#.  Use the scroll wheel to set the reference.  For GB tests, the ZERO function can be used to automatically set a reference offset to compensate for the resistance of the test leads (see page 13). Frequency (ACW, GB/MANU mode only)  Use the UP/DOWN arrow keys to bring the cursor to FREQ.  Use the scroll wheel to set the test frequency (ACW and GB mode only).
PAGE 12
GPT-9000 Series Quick Start Guide Add a Test to the AUTO Test (AUTO mode only)  Use the DOWN arrow key to bring the cursor to MANU number.  Use the scroll wheel to select a MANU test number.  Press the ADD soft-key to add the test as the last step of the AUTO test. ADD READY Status Description The tester is put into READY status when the STOP button is pressed while in VIEW status. When the tester is in READY status, it is ready to begin testing.
PAGE 13
OPERATION WARNING WARNING If Double Action is active, the START button must be pressed 500ms after the STOP button was pressed to be able to start testing. If INTERLOCK is set to ON and the interlock connector is not connected to the SIGNAL I/O port, INTERLOCK OPEN will be displayed on the screen, preventing the test from starting. See page 18 for the Common Utility settings. Return to VIEW Status  Press the MANU/AUTO key when in READY status to return to VIEW status.
PAGE 14
GPT-9000 Series Quick Start Guide Get Test Results  Wait for the MANU/AUTO test to finish. Abort MANU Test/AUTO Test  Press the STOP button  The tester will go into the STOP status. NOTE STOP If PASS/FAIL HOLD is active, the START button can be used to continue to the next step in AUTO mode whereas the STOP button can be used to cancel the test in AUTO mode. Results Results When the tester is allowed to run to completion, a MANU test or AUTO test result is shown as a PASS or FAIL.
PAGE 15
OPERATION AUTO MODE Results Overview: AUTO= 0 0 1 - * * * AU TO _ NAME # 0 1 : PASS # 0 2 : PASS # 0 3 : PASS # 0 5 : PASS #06 : FA I L #07 : FA I L #09 : #10 : #11 : #13 : #14 : #15 : # # # # 0 0 1 1 4 8 2 6 : PASS : PASS : : Step view: STEP : FREQ= 01 - 00 2 MA NU _ N AME 60Hz H I S E T = 0 1 . 0 0mA 0 100 A CW 00 33 kV RAMP I R D CW mA =000 . 1S GB RE F # = 0 0 . 0 0mA ARC= OF F PASS T I ME R = 0 0 1 .
PAGE 16
GPT-9000 Series Quick Start Guide AUTO MODE STOP status AUTO= 0 0 1 - * * * # 0 1 : PASS #02 : # 0 5 : PASS #06 : #09 : - - - #10 : #13 : - - - #14 : AU TO _ NAME PASS #03 : FA I L #07 : - - - #11 : - - - #15 : PASS FA I L - - - - - - - # # # # 0 0 1 1 4 8 2 6 : : : : PASS S TOP - - - - - - - Return to READY Status  Press the STOP button STOP Page View Description Page View is accessible by pressing the PAGE key when the tester is in AUTO mode/VIEW status. Each AUTO test contains up to 16 steps.
PAGE 17
OPERATION Move Steps  Use the arrow keys to highlight the step you wish to move.  Press the MOVE soft-key.  Use the arrow keys to move the cursor to the desired step (destination).  Press the MOVE soft-key again to move. MO V E MO V E Swap Steps  Use the arrow keys to highlight the first step you wish to SWAP.  Press the SWAP soft-key.  Use the arrow keys to move the cursor to the second step that is to be swapped.  Press the SWAP soft-key again to swap the 1st and 2nd steps that were chosen.
PAGE 18
GPT-9000 Series Quick Start Guide The step will be removed from the table as soon as the DEL soft-key is pressed. Save Page View  To save, press the EDIT/SAVE key. EDIT/SAVE The tester will return to the VIEW status. Cancel and Exit Page View  To exit and cancel any changes, press the ESC key. ESC The tester will return to the VIEW status. Common Utility Settings Description The Common Utility menu is accessed by pressing the UTILITY key when the tester is in VIEW status.
PAGE 19
OPERATION Select a Utility Setting. L CD  Choose a utility by pressing the corresponding LCD, BUZZ, INTER or CTRL soft-key. (Example)  The chosen utility will be displayed.  Use the UP/DOWN arrow keys to highlight a setting.  Use the scroll wheel to choose a parameter for the setting. NOTE The INTERLOCK function is set to OFF by default in the Common Utility>CTRL menu. To increase safety, set INTERLOCK to ON and use the accompanying Interlock connector to enable testing.
PAGE 20
GPT-9000 Series Quick Start Guide MANU Utility Settings Description The MANU Utility menu is accessed by pressing the UTILITY key when the tester is in MANU mode/EDIT status. The MANU Utility settings are configured for each MANU test separately. The settings include: ARC MODE, PASS HOLD, FAIL HOLD, MAX HOLD and GROUND MODE. MANU = * * * - 0 0 2 MANU ARC MO D E : O F F P A S S HO L D : OF F F A I L HO L D : OF F MA X HO L D : OF F G R O U N D MO D E : O N UT I L I T Y Select a Setting.