Owner Manual

ManualsBrandsHAHAEMALL ManualsBarn Door HardwareSliding Smoothly and Quietly Standard Double Door Barn Hardware Kit

1

2

3

4

5

6

Installation Manual

Barn Door Hardware

※Check the Quantities

1

● Installation Tools

Pencil Level RatchetWrenchRuler

drill

Router

Note: If you encounter any problem with the package and the following installation,

please email us at hahaemallservice@outlook.com. Please also tell us your

“ORDER ID,” we will solve any issues for you as soon as possible.

Steel Hanger

Door Stopper

Anti-jump Pad

Type A Floor guide

Type B Floor guide

Junction Plate

Part Name

Flat Track

3FT2.5FT 3.5FT 4FT 5FT 5.5FT 6FT 7FT6.6FT 7.5FT 8FT

1 1 1 2 2 2 2

0 0 0 1 1 1 1 1

1

0

2

1

2

1

2 2 2 22 2 2 2

2

22 2

2 2 2 22 2 2 2 22 2

2 2 2 22

2 3

3 3

4 5

6 6

6

6

6

2 3

3 3

4 5

6 6

6

6

6

2 2 2 22 2

1 1 1 11 1 1

1

11 1

1 1 1 11 1 1

1

11 1

Picture

Lag Bolt

Spacer

Single Door Hardware Kit Includes

Steel Hanger

Door Stopper

Anti-jump Pad

Type A Floor guide

Type B Floor guide

Junction Plate

Part Name

Flat Track

3FT2.5FT 3.5FT 4FT 5FT 5.5FT 6FT 7FT6.6FT 7.5FT 8FT

1 1 1 2 2 2 2

0 0 0 1 1 1 1 1

1

0

2

1

2

1

4 4 4 44 4 4 4

2

44 4

4 4 4 44 4 4 4 44 4

2 2 2 22 2 2 2 22 2

2 2 2 22 2 2 2 22 2

2 2 2 22

2 3

3 3

4 5

6 6

6

6

6

2 3

3 3

4 5

6 6

6

6

6

2 2 2 22 2

Picture

Lag Bolt

Spacer

Double Door Hardware Kit Includes

Summary of content (7 pages)

PAGE 1
Barn Door Hardware Installation Manual ※Check the Quantities Note: If you encounter any problem with the package and the following installation, please email us at hahaemallservice@outlook.com. Please also tell us your “ORDER ID,” we will solve any issues for you as soon as possible. Single Door Hardware Kit Includes Part Name 2.5FT 3FT 3.5FT 4FT 5FT 5.5FT 6FT 6.6FT 7FT 7.
PAGE 2
※Chart: Track Junction 3FT 2” 16” 5” 3.5FT 16” 16” 8” 4FT 5FT 7” 2” 16” 16” 7/8”(21mm) 5” 16” 7” 16” 7” 7” 16” 7” 2” 31/32”(25mm) 8” 7” 16” 7” 16” 16” 2” 1/8”(2.85mm) 5.5FT 2” 16” 16” 2” 2” 16” 16” 2” 6FT 3.8” 16” 16” 3.8” 3.8” 16” 16” 3.8” 5” 16” 16” 5” 5” 16” 16” 5” 5” 16” 16” 2”(51mm) 6.6FT 5” 7FT 8” 16” 16” 8” 7.5FT 8” 16” 16” 8” 8” 16” 16” 6-11/16”(170mm) 2.
PAGE 3
※Hardware Installation Step 1: Attach Steel Hangers to Your Doors a.Please choose the correct roller installation according to your roller shape on page 2 above and the illustration below.Recommended: The Hangers should be between 2”-4” from the door edge to the center of Hanger. b.Mark the holes for the hangers at the position shown in the above chart. Step 2: Cut Floor Guide Slot At The Bottom Of The Door a.
PAGE 4
Step 3: Install anti-jump pad As shown in the illustration, the screw is near the front edge of your door (recommended: drill pilot hole to avoid splitting). Do not over tighten. Prepare and Install the Tracks Step 4: Connect Tracks And Install Door Stoppers a.Connect your tracks with junction plates if needed. b.Loosely install the Door Stoppers near each end of the track (final positioning will be determined at the end of the installation (Step 9)).
PAGE 5
Step 6: Mark and Drill Track Holes a.Line up a Track on the line and mark the location of the holes. Note: holes are 16” apart, line up with wall studs if possible. b.Concrete wall: Drill holes by using a 1/4”concrete drill bit. c.Wood framed wall: Drill out the holes by using a drill with 5/32” drill bit.
PAGE 6
Hanging and Positioning Doors Step 8: Install Your Doors Hang your Steel Hangers on the Track, and then twist the Anti-Jump Pad toward to the wall so that it is under the Track. twist the Anti-Jump Pad toward to the wall Step 9:Install the Floor Guide Position the door at your desired close position, put half of the floor guide under the door, mark the location, and then fix guide to the floor.Position doors in your desired closed and open position and adjust Door Stoppers.
PAGE 7
Type B φ1/8” (3mm) φ5/16” (8mm) concrete wall wood wall WARNING • Failure to wear proper safety gear (i.e.,eye protection) may result in serious injury or death. Always wear proper safety gear before using power tools. • Improper operation of power tools may result in loss of control, serious injury or death. Always ensure you have complete control of the power tool and the work area is free of hazards before operatiog a power tool.