Dishwasher HDW9SST HDW9WHT Instructions for Use 012050
Index Safety Is Very Important 2 Close-up View (Control Panel) 3 Close-up View (Interior) 3 Detergent and Rinse Aid 4 Loading the Dishwasher 5 Turning on the Appliance 6 Energy Saving Tips 7 How to Keep Your Dishwasher in Shape 7 Wash Cycle Table 8 Cleaning and Special Maintenance Troubleshooting Installation 1 9 9-12 13-14 Technical data 15 Diagram 15
Safety Is Very Important Carefully read the instructions contained in this manual, as it provides information that is essential to safe and proper installation, use and maintenance of this appliance. Carefully remove and dispose of the packing material. Check to make sure that the appliance is not damaged. If in doubt, contact the retailer it was purchased from. This dishwasher is designed for washing household dishes and cooking utensils.
Close-up View (Control Panel) A "POWER" Button B "END" Light C Heat Indicator Light D Handle For Opening Door E Knob For Selecting Cycle Close-up View (Interior) 3 A Upper Rack B Rack Height Adjustor E Washing Filter F Bottom Spray Arm C Top Spray Arm D Lower Rack G Detergent and Rinse Aid Dispenser
Detergent and Rinse Aid... Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table." The detergent dispenser is located on the inside panel the door. B Loading the detergent To open the "A" cover on the dispenser, press the "B" button. The detergent for the wash cycle should be poured into the "C" compartment.
Loading the Dishwasher Before placing the dishes in the dishwasher, remove the larger food particles to prevent the filter from becoming clogged. If the pots and pans have baked-on food that is extremely hard to remove, we recommend they are soaked before washing. This will eliminate the need for extra wash cycles. Pull out the rack to load the dishwasher. Lower Rack The lower rack Place the most difficult to clean items on the bottom rack: pots, pans, lids, serving dishes and bowls.
Turning on the Appliance Starting a wash cycle... Make sure that the plug for the appliance is inserted into the wall socket. Make sure that the water supply is turned on to full pressure. Load the dishes. Pour in the detergent. Press the "POWER" button, and the “END” light will turn on. Turn the knob located on the right of the control panel until the number or symbol for the cycle setting is aligned with the refrence mark (see the section entitled, program overview).
Energy Saving Tips It is important to try and run the dishwasher when it is fully loaded to save on energy. Rather than run a full cycle for a half load, you can run the "PRE-RINSE" cycle which will prevent odours from forming and food from caking onto the dishes. Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are.
Wash Cycle Table Wash programme Detergent Types of load Description of cycle Prewash Rinse Extended Wash Very dirty dishes, pots and pans. (Not to be used with delicate items.) Pre-wash with hot water. Extended wash at 70°C. Rinses with cold water. Rinse with hot water. Drying. 5g 25g Normal load of dirty NORMAL dishes, pots and (AS/NZS 2007) pans, Standard daily cycle. Pre-wash use cold water. Extended wash at 50°C. Rinse with cold water. Rinse with hot water. Drying.
Cleaning and Special Maintenance Filter Assembly For the best performance and results, the filter assembly must be keep clean. The filter removes food particles from the wash water, allowing the water to be recirculated during the cycle. For this reason, it is a good idea to remove any food particles trapped in the filter after each wash cycle by rinsing the semi-circular filter and cup "A" under running water. To remove the filter assembly, pull the handle in an upward direction.
Troubleshooting Fault with fuse in mains electricity supply. Plug not inserted in wall socket. Appliance door not closed properly. Knob stay at the mark of "RESET" Water tap not turned on. Blocked strainer in water intake hose. - The strainer is situated in the Aquastop or supply-hose connection. Caution Do not forget that repairs should only be carried out by a qualified specialist. Improper repairs can lead to considerable equipment damage as well as danger to the user. ...
Troubleshooting the nature of the problem. the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door. Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains. Lid in detergent compartment cannot be closed Detergent compartment has been overfilled. Mechanism is clogged with remnants of detergent.
Troubleshooting ...with the dishes,cutlery, etc. Remnants of food are stuck to the dishes, cutlery,etc. Dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, etc. Too many items in the rack. Items in the rack were touching each other. Not enough detergent was added to dispenser. Selected wash programme was not intensive enough. Rotation of spray arm was obstructed by dishes, etc. Nozzles in spray arm are blocked by remnants of food. Filters are blocked.
Installation Positioning the Appliance Position the appliance in the desired location. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or left to allow correct installation. Levelling the Appliance Once the appliance is positioned, adjust the feet by screwing them in or out. The appliance should not be inclined more than 2 degrees, to ensure proper performance.
Installation Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink. Use the plastic support that comes with the appliance (see fig .2) and ensure there are no tight bends or kinks. The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. MAX 100 MIN 40 fig.2 Attention: The plastic hose support must be fastened to the wall to prevent the drain hose from moving.
Technical data Width 45 cm Depth 60 cm Height 85 cm Capacity 9 standard place settings Mains water pressure 0.03-1.
