Product Brochure

Specifi cations, compliances and dimensions subject to change without notice
6
INCH
EATON Halo Product Catalog 6" Recessed Downlighting
6-3
6" ICAT, Air-Tite, Remodel, LED Housing, 120V/277V
The H750RICAT is a LED remodel housing to be used with
compatible Halo LED modules and trims. The H750RICAT is
designed for remodel applications in insulated ceilings and
can be in direct contact with ceiling insulation*. The Air-Tite
™
housing design restricts airfl ow between conditioned spaces
and unconditioned areas. The H750RICAT LED connector
system provides high effi cacy code compliance when used
with compatible Halo LED lighting systems.
H750RICAT
Features
Housing
•
Single wall aluminum housing
•
Openings are gasketed for Air-Tite
™
•
Designed for insulated ceilings in direct contact with
insulation* (May also be installed in non-insulated ceilings)
•
For installation from below the finished ceiling.
Integral flange secures fixture against ceiling.
•
Halo identity embossed on can top
Remodel Springs
Four remodel clips secure housing and accommodate
1/2" and 5/8" ceiling material
Includes:
•
Slide-N-Side
™
junction box wire traps (Details Pg. 9)
•
Quick Connect
™
push wire nuts (Details Pg. 9)
•
Air-Tite
™
code compliant (Details Pg. 9)
LED Module Connection
•
Halo LED modules install with a plug-in 120V/277V
rated line voltage wiring connector (UL and CSA Listed
luminaire disconnect)
•
This non-screw base connection preserves the high
efficacy rating and prevents use of low efficacy sources
(See LED module specifications)
Application Note
LED connection is rated for 120V and 277V input.
Installer must verify LED module voltage is compatible
with the applicable voltage input. If uncertain, consult
a qualified electrician.
Compliance
•
cULus Listed 1598 luminaire
•
cULus Listed damp location
•
cULus Listed for wet location,
covered ceiling, with select trims
•
cULus Listed for feed through
•
cULus Listed for direct contact with
insulation and combustible material*
•
CE Marking - "Conformité Européene" conformity with
the Council of European Communities Directives, meeting
internationally recognized compliance with used with
ML56 series LED modules
•
Air-Tite code compliant. Certified under ASTM E283;
not exceeding 2.0 cfm (0.944 L/s) air leakage rate
tested at a 1.57 psf (75 Pa) pressure differential.
•
Rated for 20W maximum
•
Use with designated Halo LED systems for
ENERGY STAR
®
certification
•
Can be used for State of California Title 24 high efficacy
compliance with Title 20 Certified Halo LED
•
Can be used for International Energy Conservation Code
(IECC) high efficacy compliance with designated LED
modules and trims
•
Refer to LED module specification sheets online
for additional compliance information
•
RoHS compliant
*Not to be used in direct contact with spray foam insulation
(Consult NEMA LSD57-2013)
Special Features
Slide-N-Side
™
junction box
Quick Connect
™
push wire nuts
Air-Tite
™
code compliant
LED Housing
Compatible LED Modules & Trims
ML56 with 69x series trims
SLD6
RL56
RA56
LT56
H750RICAT
1/2" to 5/8"
[13mm to 15mm]
7"
[178mm]
Ceiling opening to match
template supplied
6-1/4”
[159mm]
13-1/4"
[337mm]
6-7/8"
[175mm]