Product Brochure

Specifi cations, compliances and dimensions subject to change without notice
6
INCH
EATON Halo Product Catalog 6" Recessed Downlighting
6-14
LED Surface Mount
SLD6 - Universal Voltage Series
.7”
[17.28mm]
.8”
[21.46mm]
7.79”
[197.87mm]
5"/6" Surface LED Retrofi t Module
The Halo Surface LED Downlight (SLD) incorporates WaveStream
™
technology to create an ultra-low profi le surface mounting luminaire with
the performance and look of a traditional downlight. SLD6-1200 UNV series
is designed for installation in many 4" x 2-1/8" deep square junction boxes.
Accessory mounting kit allows retrofi t in 5" and 6" IC and Non-IC recessed
housings.* Suitable for residential or commercial installations. Ideal for
closets, storage areas, attics and basements. Compliant with NFPA
®
70,
NEC
®
Section 410.16 (A)(3) and 410.16 (C)(5).
Features
Mechanical
Die cast aluminum trim ring, and die formed aluminum frame
Optics
•
WaveStream
™
technology provides uniform luminance
from a low profile flat lens
•
AccuAim
™
optics provide directional control for the “cone-
of-light” beam distribution of a traditional downlight
•
Precision molded lens features high transmission polymer
with UV stabilized protecting film
Electrical Junction Box Mounting
•
SLD may be used in compatible electrical junction
boxes in direct contact with insulation including spray
foam insulation
•
Suitable for installation in many 4" x 2-1/8" deep square
electrical junction boxes
•
Compatible with other junction boxes with accessory
SLD6EXT extension spacer ring
Note: Driver consumes 3 cubic inches of junction box
•
Surface mounting in a fire-rated ceiling using an
appropriate electrical box offers a cost-effective
alternative to fire-rated recessed housings
Note: Fire-rating is per the rating of the ceiling and
applicable junction box, not the SLD
•
Installer must ensure compatibility of fit, wiring
and proper mounting in the electrical junction box.
This includes all applicable national and local
electrical and building codes.
•
Proprietary Slot-N-Lock quick installation system
for junction box installation
•
T-bracket with Slot-N-Lock mounting tabs included
Recessed Housing Mounting
•
Accessory SLD6ACCKIT required for mounting
in 5" and 6" enclosed recessed housings
•
May be installed in IC recessed housings in
direct contact with insulation
Note: Not for use in recessed housings in direct contact
with spray foam insulation (Refer to NEMA LSD 57-2013)
•
The SLD6 may be used with any 5 or 6 inch diameter
recessed housing constructed of steel or aluminum with
an internal volume that exceeds 107.9 in³
LED
•
Linear LED arrays are integrated in trim perimeter
•
Correlated Color Temperature (CCT):
2700K, 3000K, 3500K, 4000K
•
Color Rendering Index (CRI): 80 and 90
•
Lumens – see Energy Data
•
Lumen maintenance L70 at 50,000 hours
Electrical Connections
Junction Box
•
Compatible with 4" x 2-1/8" deep square boxes
•
Supply wire adapter with LED quick connector included
•
LED connector is a non-screw base luminaire disconnect
Recessed Housings
•
Accessory SLD6ACCKIT required
•
LED connector is compatible with Halo 5" H550 series
and 6" H750, H2750 series LED housings
•
LED Connector meets California Title 24 high efficacy
luminaire standard as a non-screw base
LED Driver
•
Driver is a 120V-277V universal voltage input, high
efficiency, dimmable electronic power supply providing
DC power to the LED arrays
•
Driver features high power factor, low THD, and
has integral thermal protection in the event of over
temperature or internal failure
•
Driver is replaceable if it should be required
•
If dimming is not required the fixture can be operated
from a standard wall switch
Dimming - Phase Control
•
Designed for continuous dimming capability to nominally
5% with many 120V Leading Edge (LE) and Trailing Edge
(TE) phase control dimmers. Dimmers with low end trim
adjustment offer greater assurance of achieving 5% level.
•
Consult dimmer manufacturer for compatibility and
conditions of use. (Note some dimmers require a neutral
in the wallbox)
Dimming - 0-10V
•
Dimmable to 10% in typical operation with compatible
0-10V DC low voltage dimmers
•
0-10V DC dimmers operate using two low voltage
dimming wires (color coded violet and gray). The low
voltage dimming wires are separate from the
120V AC or 277V AC power.
•
Switching on/off is via the line voltage (120V AC
or 277V AC) power, and dimming is controlled via
the 2-wire 0-10V DC wiring
Compliance
•
cULus Listed ceiling and wall
•
cULus Listed damp location, ceiling and wall
•
cULus Listed wet location, covered ceiling only
(shower rated)
•
Suitable for use in closets, compliant with NFPA
®
70,
NEC
®
Section 410.16 (A)(3) and 410.16 (C)(5)
•
SLD may be used in compatible electrical junction
boxes in direct contact with insulation including
spray foam insulation
•
May be installed in IC recessed housings in direct
contact with insulation. Not for use in recessed
housings in direct contact with spray foam insulation.
(Refer to NEMA LSD 57-2013)
•
EMI/RFI: meets FCC 47CFR Part 15 Class B limits, and is
suitable for use in residential and commercial installations
•
Air-Tite code compliant. Certified under ASTM E283;
not exceeding 2.0 cfm (0.944 L/s) air leakage rate
tested at a 1.57 psf (75 Pa) pressure differential
•
90 CRI (R9 > 50) can be used to comply with California
Title 24 high efficacy requirements. Title 20 Certified
for residential compliance.
•
80 CRI can be used to comply with California Title 24
non-residential lighting controls requirements
as a LED luminaire
•
Can be used for International Energy Conservation Code
(IECC) high efficacy luminaire compliance
•
ENERGY STAR
®
certified downlight surface retrofit
•
Contains no mercury or lead and RoHS compliant
•
Photometric testing in accordance with IES LM-79
•
Lumen maintenance projections in accordance with
IES LM-80 and TM-21
90 CRI 80 CRI
SLD612 - 1200 Series UNV, 120V-277V