Product Brochure

4
INCH
Specifi cations, compliances and dimensions subject to change without notice
EATON Halo Product Catalog 4" Recessed Downlighting
4-2
Housing
•
Double wall aluminum construction helps
dissipate heat. The inner housing can be adjusted
in the plaster frame to compensate for different
ceiling materials.
•
Designed for insulated ceilings in direct contact
with insulation* (May also be installed in
non-insulated ceilings)
•
Inner housing adjusts for ceilings up to 1" thick
Plaster Frame
•
Galvanized steel die-formed construction
•
The housing can be removed from plaster frame
to provide access to the junction box
•
Plaster frame features include:
• Patented regressed locking screw positioned for
securing hanger bars from below the ceiling
• Cutouts for easily crimping hanger bars in position
• Air-Tite aperture gasket is pre-installed
• Halo identity embossed on plaster frame
Includes:
•
Got Nail!
™
bar hangers (Details Pg. 7)
•
Pass-N-Thru
™
bars (Details Pg. 7)
•
Slide-N-Side
™
junction box wire traps (Details Pg. 7)
•
Quick Connect
™
push wire nuts (Details Pg. 7)
•
Air-Tite
™
code compliant (Details Pg. 7)
LED Module Connection
Compatible Halo LED modules simply install with a
plug-in line voltage wiring connector (UL and CSA
Listed Luminaire Disconnect). This non-screw base
LED connection preserves the high efficacy rating of
the luminaire (see also LED Module specifications).
Compliance
•
cULus Listed 1598 luminaire
•
cULus Listed for damp location
•
cULus Listed for wet location,
covered ceiling, with select trims
•
cULus Listed for feed through
•
cULus Listed for direct contact with
insulation and combustible material*
•
Use with designated Halo LED systems for
ENERGY STAR
®
certification
•
Can be used for State of California Title 24 high efficacy
compliance with designated Halo LED lighting systems.
•
Can be used for International Energy Conservation Code
(IECC) high efficacy compliance with designated Halo LED
lighting systems.
•
Air-Tite code compliant. Certified under ASTM E283;
not exceeding 2.0 cfm (0.944 L/s) air leakage rate
tested at a 1.57 psf (75 Pa) pressure differential
*Not to be used in direct contact with spray foam insulation
(consult NEMA LSD57-2013)
4" IC, Air-Tite, New Construction LED Housing
The H995ICAT is a dedicated LED small aperture IC Air-Tite
™
housing
for use with Halo RA4, RL4, LT4 series LED modules and may be used
with SLD4 series with the SLD spring kit. It is designed for use in
insulated ceilings where it will be in direct contact with insulation*.
It is an Air-Tite
™
housing designed to restrict air fl ow between
conditioned spaces and unconditioned areas. The LED connection is
non-screw base to preserve the high effi cacy rating of the luminaire.
H995ICAT
Features
LED Housing
H995ICAT
1/2 inch
[13 mm]
4-3/8 inch
[111mm]
Ceiling opening
5-1/2 inch
[140mm]
5-1/4 inch
[133mm]
8-1/2 inch
[216mm]
Compatible LED Modules
RA4
RL4
SLD4
LT4
Special Features
Got Nail!
™
bar hangers
Pass-N-Thru
™
bars
Slide-N-Side
™
junction box
Quick Connect
™
push wire nuts
Air-Tite
™
code compliant