Product Brochure

Specifi cations, compliances and dimensions subject to change without notice
5
INCH
EATON Halo Product Catalog 5" Recessed Downlighting
5-9
LED Surface Mount
SLD6 - 600 & 1200 Series
.7”
[17.28mm]
.8”
[21.46mm]
7.79”
[197.87mm]
5"/6" Surface LED Retrofi t Module – 5 Inch Application
The Halo Surface LED Downlight (SLD) incorporates WaveStream
™
technology
o create an ultra-low profi le surface mounting luminaire with the performance
and look of a traditional downlight. SLD6 is designed for installation in many
3-1/2" and 4" square, octagon or round junction boxes. And may also retrofi t
in 5" and 6" IC and Non-IC recessed housings.* Suitable for residential or
commercial installations. Ideal for closets, storage areas, attics and basements.
Compliant with NFPA
®
70, NEC
®
Section 410.16 (A)(3) and 410.16 (C)(5).
Features
Mechanical
Die cast aluminum trim ring, and die formed
aluminum frame
Optics
•
WaveStream
™
technology provides uniform
luminance from a low profile flat lens
•
AccuAim
™
optics provide directional control
for the “cone-of-light” beam distribution of a
traditional downlight
•
Precision molded lens features high transmission
polymer with UV stabilized protecting film
Electrical Junction Box Mounting
•
SLD may be used in compatible electrical junction
boxes in direct contact with insulation including
spray foam insulation
•
Suitable for installation in many 3-1/2" and 4"
square, octagon, and round electrical junction boxes
Note: Driver consumes 3 cubic inches of junction box
•
Surface mounting in a fire-rated ceiling using an
appropriate electrical box offers a cost-effective
alternative to fire-rated recessed housings
Note: Fire-rating is per the rating of the ceiling and
applicable junction box, not the SLD
•
Installer must ensure compatibility of fit, wiring
and proper mounting in the electrical junction box.
This includes all applicable national and local
electrical and building codes.
•
Proprietary Slot-N-Lock quick installation system
for junction box installation
•
T-bracket with Slot-N-Lock mounting tabs included
Recessed Housing Mounting
•
May be installed in IC recessed housings in direct
contact with insulation
*Note: Not for use in recessed housings in direct contact
with spray foam insulation (Refer to NEMA LSD 57-2013)
Torsion Spring 5" & 6" Kit (Included)
•
The torsion springs adjust on the frame to fit
5" or 6" compatible housings
Friction Blade 5" & 6" Kit (Included)
•
For retrofit in 5" and 6" housings without torsion
spring mounting tabs
•
Allows the SLD to be installed in any position within
the housing aperture (360 degrees)
LED
•
Linear LED arrays are integrated in trim perimeter
•
Correlated Color Temperature (CCT):
2700K, 3000K, 3500K, 4000K
•
Color Rendering Index (CRI): 80 and 90
•
Lumens – see Energy Data
•
Lumen maintenance L70 at 50,000 hours
Electrical Connections
Junction Box
•
Compatible with 3-1/2" x 2" and 4" x 1-1/2" deep
round, square and octagon boxes (2-1/8" deep
boxes recommended)
•
Supply wire adapter with LED quick connector included
•
JB models for use in junction boxes. May be used in
recessed housings with accessory SLD6ACCKIT.
Recessed Housings
•
LED connector is a non-screw base luminaire
disconnect compatible with Halo 5" H550 series
and 6" H750/H2750 series LED housings
•
LED connector meets California Title 24 high efficacy
luminaire standard as a non-screw base
•
E26 Edison screw base included
LED Driver
•
Driver is a 120V input, high efficiency, dimmable
electronic power supply providing DC power to
the LED arrays
•
Driver features high power factor, low THD,
and has integral thermal protection in the event
of over temperature or internal failure
•
If dimming is not required the fixture can be
operated from a standard wall switch
Dimming
Designed for continuous dimming capability to nominally
5% with many 120V Leading Edge (LE) and Trailing Edge
(TE) phase control dimmers. Dimming to 5% is best assured
using dimmers with low end trim adjustment. Consult
dimmer manufacturer for compatibility and conditions of
use. Note, some dimmers require a neutral in the wallbox.
Compliance
•
cULus Listed ceiling and wall
•
cULus Listed damp location, ceiling and wall
•
cULus Listed wet location, covered ceiling only
(shower rated)
•
Suitable for use in closets, compliant with NFPA
®
70, NEC
®
Section 410.16 (A)(3) and 410.16 (C)(5)
•
May be used in compatible electrical junction boxes
in direct contact with insulation including spray
foam insulation
•
May be installed in IC recessed housings in direct
contact with insulation (Not for use in recessed
housings in direct contact with spray foam insulation.
Refer to NEMA LSD 57-2013)
•
UL Classified when used in retrofit with listed housings
(See housing compatibility)
•
EMI/RFI: meets FCC 47CFR Part 15 Class B limits,
and is suitable for use in residential and commercial
•
90 CRI (R9 > 50) can be used to comply with California
Title 24 high efficacy requirements. Title 20 certified
for residential compliance.
•
80 CRI can be used to comply with California Title 24
non-residential lighting controls requirements as a
LED luminaire
•
Can be used for International Energy Conservation Code
(IECC) high efficiency luminaire compliance
•
ENERGY STAR
®
certified downlight surface retrofit
•
Contains no mercury or lead and RoHS compliant
•
Photometric testing in accordance with IES LM-79
•
Lumen maintenance projections in accordance with
IES LM-80 and TM-21
90 CRI 80 CRI
SLD606 - 600 Series, 120V
SLD612 - 1200 Series, 120V