Item #1001 846 203 Model # IYG8011L-2/CR USE AND CARE GUIDE LED INTERIOR FLUSHMOUNT Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this LED interior flushmount. We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required........................................... 3 Hardware Required.................................... 3 Package Contents...................................... 4 Installation....................................................5 Care and Cleaning..................................... 7 Troubleshooting......................................... 7 Table of Contents.......................................2 Safety Information..................................... 2 Warranty..............
Pre-Installation PLANNING INSTALLATION NOTE: Keep your receipt and these instructions for proof of purchase. TOOLS REQUIRED Wire Strippers Safety Goggles Flathead Screwdriver Phillips Screwdriver Ladder Gloves Electrical Tape Wire Cutters HARDWARE REQUIRED NOTE: Hardware not shown to actual size.
Pre-Installation (continued) PACKAGE CONTENTS A B Part Description Quantity A Canopy 1 B Shade 1 4
Installation 1 □ □ □ □ Attaching the mounting strap to the outlet box 2 Screw the hex nut (DD) about 1 in. onto the nipple (FF). Screw the nipple (FF) about 1/2 in. into the mounting strap (EE). Tighten the hex nut (DD) against the mounting strap (EE) to secure the nipple (FF). Mount the mounting strap (EE) to the outlet box (not included) using the two outlet box screws (CC).
Installation (continued) 3 Securing the canopy to the outlet box □ Align the nipple (FF) to protrude through the hole in the center of the canopy (A). Place the canopy (A) over the outlet box. Screw the mounting nut (GG) onto the nipple (FF) to secure the canopy (A). □ □ 4 □ □ □ Attaching the shade Align the three slots on the shade (B) with the three divots located inside the canopy (A). Carefully turn the shade (B) clockwise until it locks into the canopy (A).
Care and Cleaning □ □ Clean the fixture with a soft, dry cloth. Do not use any cleaners with chemicals, solvents or harsh abrasives. CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Troubleshooting Problem Possible Cause The fixture will not light. □ The power is off. Solution □ Ensure the power supply is On. □ The circuit breaker is □ Ensure the circuit breaker is in the On position.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Artículo #1001 846 203 Modelo #IYG8011L-2/CR U GUÍA DE USO Y MANTENIMIENTO INTERIOR LED DE EMPOTRAR Preguntas, problemas o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay de Lunes a Viernes entre 8 a.m. y 7 p.m., El Sábado entre 9 a.m. y 6 p.m., (hora del Este de EE. UU.) 1-855-HD-HAMPTON HAMPTONBAY.COM GRACIAS POR TU COMPRA Agradecemos la confianza que ha tenido en Hampton Bay a traves de de la compra de este luz interiores LED de empotrar.
Índice Herraminentas Necesarias....................... 11 Requiere de Hardware............................. 11 Contenido del Paquete............................. 12 Instalación..................................................13 Mantenimiento y Limpieza....................15 Solución de Problemas..........................15 Índice........................................................... 10 Información de Seguridad.................... 10 Garantía......................................................
Pre-Instalación PLANIFICACIÓN DE LA INSTALLATIÓN Lee todas las instrucciones antes de ensamblar. Antes de comenzar la instalación o de quitar la instalación anterior, desconecte la alimentacion apagando el interruptor del circuito o quitando el fusible en la caja de fusible. Para evitar dañar el artículo, ensámblalo sobre una superficie suave, no abrasiva, como por ejemplo una alfombra o cartón. NOTA: Conserva el recibo y estas Instrucciones como Comprobante de Compra.
Pre-Instalación (continuación) CONTENIDO DEL PAQUETE A B Pieza Descripción Cantidad A Dosel 1 B Pantalla 1 12
Instalación 1 Acoplar la correa de montaje a la caja de salida 2 □ Apriete la tuerca hexagonal (DD) como una pulgada dentro de la boquilla (FF). Atornille la boquilla (FF) como media pulgada dentro de la correa de montaje (EE). Apriete la tuerca hexagonal (DD) contra la correa de montaje (EE) para asegurar la boquilla (FF). Coloque la correa de montaje (EE) en la caja de salida (no incluido) usando los dos tornillos de la caja de salida (CC).
Instalación (continuación) 3 Asegurar el dosel a la caja de salida □ Alinee la boquilla (FF) para que sobresalga pro el orificio en el dosel (A). Coloque el dosel (A) sobre la caja de salida. Atornille el tuerca de tapa (GG) en la boquilla (FF) para asegurar el dosel (A). □ □ 4 □ □ □ Fijar la pantalla At aliñe los tres espacios en la pantalla (B) con las tres marcas situado en el interior del dosel (A).
Mantenimiento y Limpieza □ □ Limpia la lámpara con un paño suave y seco. No uses limpiadores con químicos, solvents, o productos abrasivos. PRECAUCIÓN: Antes de intentar limpiar la pieza, desconéctela o apague el interruptor o remueva el fusible de la caja de fusibles. Solución de Problemas Problema Causa Posible El accesorio no iluminará. Solución □ La electricidad está □ Asegúrate de que el suministro de electricidad esté encendido. □ El cortacircuito está apagado.
Preguntas, problemas o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay de lunes a Viernes entre 8 a.m. y 7 p.m.,,El sábado entre 9 a.m. y 6 p.m., (hora del Este de EE. UU.) 1-855-HD-HAMPTON HAMPTONBAY.COM Conserva este manual para referencias futuras.
Article #1001 846 203 Modèle#IYG8011L-2/CR GUIDE D'UTILISATION ET D'ENTRETIEN LUMIÈRE LED PLAFONNIER INTERIEUR Questions, problèmes, pièces manquantes? Avant de retourner au magasin, veuillez communiquez avec le service à la clientèle Hampton Bay entre 8h00 et 19h00 (HNE) du lundi au vendredi, entre 9h00 et 18h00 (HNE) du samedi 1-855-HD-HAMPTON HAMPTONBAY.COM MERCI Nous vous remercions de la confiance que vous avez place en Hampton Bay en achetant ce lumière LED plafornnier interieur.
Table des Matières Outils Requis............................................ 19 Le Materiel Requis................................... 19 Contenu de l'emballage............................20 Installation..................................................21 Entretien et nettoyage............................23 Dépannage.................................................23 Table des matières..................................18 Consignes de sécurité........................... 18 Garantie...........................
Pré-Installation PLANIFICATION DE L'INSTALLATION Lisez toutes les instructions avant de procéder à l’assemblage. Avant de commencer à installer ce luminaire ou d’enlever l’ancien luminaire, déconnectez le courant en eteignant le disjoncteur ou en enlevant le fusible correspondent du coffret à fusibles. Pour éviter d’endommager ce produit, assemblez-le sur une surface molle et non abrasive telle qu’un tapis ou un carton. REMARQUE: Conservez le reçu, ainsi que ces instructions, à titre de preuve d’achat.
Pré-Installation (suite) CONTENU DE L'EMBALLAG A B Pièce Description Quantité A Pavillon 1 B Abat-jour 1 20
Installation 1 Attacher la sangle de montage à la boîte de sortie 2 □ Visser l’écrou hexagonal (DD) d’environ un pouce sur l’embout (FF). Visser l’embout (FF) d’environ un demi pouce sur la sangle de montage (EE). Serrer l’écrou hexagonal (DD) sur la sangle de montage (EE) pour sécuriser l’embout (FF). Monter la sangle de montage (EE) sur la boîte de sortie (non inclus) grâce aux deux vis de la boîte de sortie (CC).
Installation (suite) 3 Fixer le pavillon sur la boîte de sortie □ Aligner l’embout (FF) afin qu’il ressorte par le trou situé dans le centre du pavillon (A). Placer le pavillon (A) sur le boîte de sortie. Visser écrou de chapeau (GG) l’embout (FF) sur le pavillon (A). □ □ 4 □ □ □ Fixer le abat-jour Alignez les trois fentes sur l’abat-jour (B) à l’aide des trois mottes situé à l'intérieur de la pavillon (A).
Entretien et Nettoyage □ □ Nettoyez la lampe avec un linge doux, sec. N'utilisez jamais de nettoyant contenant des produits chimiques, des solvants ou des abrasifs. AVERTISSEMENT: Débrancher l’alimentation électrique avant de nettoyer le luminaire en enlevant les fusibles concernés ou en désactivant le disjoncteur. Dépannage Problème Cause possible Le luminaire ne s'allume pas. □ Le courant est coupé. □ Assurez-vous que la source de courant électrique est sous tension.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, veuillez communiquez avec le service à la clientèle Hampton Bay entre 8h00 et 19h00 (HNE) du lundi au vendredi, entre 9h00 et 18h00 (HNE) du samedi 1-855-HD-HAMPTON HAMPTONBAY.COM Conservez ce guide pour un usage ultérieur.