Installation Guide

STEP 4: INSTALL REMAINING CABINETS
Drill a 3/16" pilot hole at the stud locations through the back panel and into the stud. Level and mount the cabinet to the wall with #10 x 3" screw. If needed,
shim the cabinet to level. DO NOT COMPLETELY TIGHTEN MOUNTING SCREWS UNTIL ALL CABINETS HAVE BEEN ATTACHED TOGETHER. After all
cabinets have been attached together and are level and secure, then tighten all mounting screws. Take care to seat mounting screws tightly against back rail
or panel without driving into back rail or panel material. Check to be sure that all cabinets remain level after tightening.
NOTE: To attach a wall cabinet to a TALL PANTRY unit, drill a 1/8" pilot hole 7/8" deep through the wall cabinet face frame to the tall pantry unit. Use a
#8 x 1-5/8" screw to secure cabinets together.
PASO 4: INSTALACION DE LOS GABINETES RESTANTES
Taladre un oricio guía de 3/16 pulgada en la ubicación de los montantes a través del panel trasero y en el montante. Nivele y monte el gabinete a la pared con tornillos de #10 x 3 pulgadas. NO APRIETE
COMPLETAMENTE LOS TORNILLOS HASTA QUE EL TODOS LOS GABINETES ESTÉN ACOPLADOS ENTRE SÍ. Después de acoplar todos los gabinetes entre sí y que estén jos y a nivel, apriete todos
los tornillos de montaje. Tenga cuidado de asentar los tornillos rmemente contra el panel o riel trasero sin penetrar en el material del panel o riel trasero. Revise para asegurarse de que todos los gabinetes
permanezcan a nivel después de apretar los tornillos.
NOTA: Para jar un gabinete de pared a una unidad de DESPENSA ALTA, taladre un oricio guía de 1/8 pulgada a 7/8 pulgada de profundidad a través del marco de supercie del gabinete de pared hacia la
unidad de despensa alta. Use un tornillo de #8 x 1-5/8 pulgadas para jar los gabinetes entre sí.
STEP 5: KITCHEN DRAWER ADJUSTMENT
After you install all of your cabinets, it may be necessary to adjust the drawer fronts so they are level and have the proper reveals. To better secure adjustment,
loosen the screws holding the drawer glides to the frame of the cabinet and adjust the drawer, then tighten the screws. Drill a 1/8" pilot hole through the
second hole below and drive a #8 x 5/8" screw to x the drawer in place.
PASO 5: AJUSTE DE LAS GAVETAS DE COCINA
Después de instalar todos los gabinetes, puede ser necesario ajustar los frentes de las gavetas para que estén a nivel y tengan el espacio apropiado. Para un ajuste mejor, aoje los tornillos que sostienen los
deslizadores de gavetas al marco de los gabinetes y ajuste la gaveta, apriete luego los tornillos. Taladre un oricio guía de 1/8 pulgada a través del segundo oricio de abajo y pase un tornillo de #8 x 5/8 pulgada
para jar la gaveta en su lugar.
*The fastening solutions described here are recommendations only, and are based on commonly used installations. Each installer must evaluate the specic
characteristics of the particular wall on which the cabinets are to be installed to ensure the proper fastening solution is used and the product is fastened safely
and securely. This may require hardware or fastening methods which are different from, or additional to, what is described here. RSI DOES NOT WARRANT
THE INSTALLATION OF THIS PRODUCT.
*Las soluciones de sujeción aquí descritas representan únicamente recomendaciones y se basan en procedimientos tradicionales de instalación. Cada instalador debe evaluar las características especícas de
la pared en particular donde se instalarán los gabinetes para garantizar que se use la solución de sujeción apropiada y que el producto quede jo de manera segura. Ello podría requerir métodos o herrajes de
sujeción distintos o adicionales a los aquí descritos. RSI NO GARANTIZA LA INSTALACIÓN DE ESTE PRODUCTO.
1. Loosen screw and make vertical
adjustments.
1. Aoje el tornillo y haga los ajustes verticales.
2. Cabinet drawers and doors should line up as
shown below.
2. Las puertas y gavetas de los gabinetes deben estar alineadas como se
muestra abajo.