User's Guide

ManualsBrandsHAN NETWORKS ManualsComputers & AccessoriesHAN Access Point

Table 2

Ethernet Port Pinout

Connector

Signal

Name

PoE

RJ45_DA+

PoE-

RJ45_DA–

PoE-

RJ45_DB+

PoE+

RJ45_DC+

PoE+

RJ45_DC–

PoE+

RJ45_DB–

PoE+

RJ45_DD+

PoE-

RJ45_DD–

PoE-

Table 3

Console Port Pinout

Connector

Signal Name

Function

TXD

Transmit

GND

Ground

GND

Ground

RXD

Receive

Pins not listed are not connected.

Table 4

RS-485 Port Pinout

Connector

Signal Name

Function

RS485_B

Data-

RS485_A

Data+

GND

Ground

GND

Ground

PSE_12V

12V+ OUT

PSE_12V

12V+ OUT

Pins not listed are not connected.

 Note: The serial console port allows you to connect the AP to a

serial terminal or a laptop for direct local management. This port

is an RJ-45 female connector with the pinouts described in Table 3.

Currently for use by Service & Support only.

Note: The RS-485 port allows you to connect the AP to a RS-485

terminal. The maximum allowable current of PSE 12V power output

is 300mA. In addition, PSE 12V power output can be turned on and

off by software. This port is an RJ-45 female connector with the

pinouts described in Table 4.

Power

The AP311 series access point supports direct DC power adapter (48V

DC nominal, sold separately) and Power over Ethernet (PoE).

The DC power connector port is located on the back of the device, as

shown in Figure 3.

The PoE allows the Ethernet port to draw power from an IEEE

802.3at compliant source.

HAN Access Point supports the power adapter provided by HAN ONLY.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-installation Checklist

Before installing your AP311 Stellar access point, be sure that you

have the following items:

• 8-conductor, CAT5 or better UTP cable of required length.

• One of the following power sources:

◼ IEEE 802.3at compliant Power over Ethernet (PoE) source

(PoE switch or PoE injector).

◼ AC-DC adapter (sold separately)，output voltage DC 48V,

output current ≥0.6A

• A terminal or a notebook

Identifying Specific Installation Locations

You can mount the HAN Access Points on a ceiling rail or on a wall.

You should first determine the location of the installation. The

installation position is located at the center of the required

coverage area and should be free from obstructions or obvious

sources of interference.

• Minimize the number of obstructions (such as walls) between the

AP and user terminals.

• Electronic equipment or devices (such as microwave ovens) which

may produce radio frequency noise should be away from the

installation position of the AP.

It is strictly prohibited to install around stagnant water, water seepage,

leakage or condensation. Avoid cable condensation or water seepage

along the cables connecting to the AP.

AP Installation

Refer to mounting kits installation Guide.

Verifying Post-Installation Connectivity

The LED on the AP can be used to verify that the AP is receiving power

and initializing successfully.

Product Specifications

AP311 series Dimensions/Weight

Unboxed AP311:

• Net Weight: 1.64lbs / 0.74kg

• Dimensions (HxWxD): 7.1 inches x 7.1 inches x 1.42 inches

(18 cm x 18cm x 3.6cm)

Environmental

• Operating :

▪ Temperature: 0°C to +50°C (+32°F to +122°F)

▪ Humidity: 10% to 90% non-condensing

• Storage and transportation :

▪ Temperature: -40°C to +70°C(-40°F to +158°F)

For additional specifications on this product, please refer to the

Datasheet.

HAN Access Point

AP311 Regulatory Compliance and Safety

Information

xxxxxx-xx Rev. A

*xxxxxx-xx Rev. A*

◼ Introduction

This document contains domestic and international regulatory compliance

information for the access point. To ensure that this device complies with the

regulatory standards for your region, please refer to the content below.

FCC Part 15:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generate, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one of the

following measures:

⚫ Reorient or relocate the receiving antenna.

⚫ Increase the separation between the equipment and receiver.

⚫ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

⚫ Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause

undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

RF exposure warning

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment.

This product may not be collocated or operated in conjunction with any other

antenna or transmitter

This equipment must be installed and operated in accordance with provided

instructions and the antenna(s) used for this transmitter must be installed to

provide a separation distance of at least 20 cm from all persons and must not be

collocated or operating in conjunction with any other antenna or transmitter.

California Proposition 65 Warning

WARNING: This product contains chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm.