Video Access Control Terminal Video Access Control Terminal Quick Start Guide V1.1.
Video Access Control Terminal Quick Start Guide ©2016 Hangzhou Hikvision Digital Technology Co., Ltd. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual.
Video Access Control Terminal Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Video Access Control Terminal Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
Video Access Control Terminal Contents Contents ............................................................................................................................................ 1 1 Installation ...................................................................................................................................... 2 2 Terminal Connection ....................................................................................................................... 3 2.
Video Access Control Terminal 1 Installation Before You Start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that the wall is strong enough to withstand three times the weight of the terminal. Set the DIP address before installation. Steps: 1. Connect the cables with the connecter on the rear panel of the device. Route the cables through the cable hole of the mounting plate.
Video Access Control Terminal 2 Terminal Connection 2.
Video Access Control Terminal Group Group A Group B Group C Group D Group E No.
Video Access Control Terminal 3 Wiring Description 3.
Video Access Control Terminal 3.2 The Wiring of External Card Reader 3.2.1 The Wiring of External RS-485 Card Reader Figure 3-2 External RS-485 Card Reader Connection Diagram 3.3 Card Reader Connection The access control terminal can be switched into the card reader mode. It can access to the access control as a card reader, and supports Wiegand communication port and RS-485 communication port.
Video Access Control Terminal Set the working mode of the terminal as card reader, if the terminal is required to work as a card reader. The card reader mode support to communicate by Wiegand or RS-485. The distance of Wiegand communication should be no longer than 80 m. The external power supply and the access control terminal should use the same GND cable. 3.3.
Video Access Control Terminal 4 Activating the Access Control Terminal Purpose: You are required to activate the terminal first before using it. Activation via SADP, and Activation via client software are supported. The default values of the control terminal are as follows. The default IP address: 192.0.0.64. The default port No.: 8000. The default user name: admin. 4.
Video Access Control Terminal 6. Figure 4-2 Modify Network Parameters Interface Input the password and click the Modify button to save your IP address modification. 4.2 Activating via Client Software The client software is versatile video management software for multiple kinds of devices. Get the client software from the supplied disk or the official website, and install the software according to the prompts. Follow the steps to activate the control panel. Steps: 1.
Video Access Control Terminal Figure 4-3 Control Panel Interface 2. 3. 4. 5. Click interface. icon on the control panel to enter the access control device management Figure 4-4 Online Device List Select an inactive device in the Online Device list. Click the Activate button to pop up the Activation interface. Create a password and input the password in the password field, and confirm the password.
Video Access Control Terminal 6. 7. 8. 9. Figure 4-5 Input Password Window Click OK button to start activation. Click the Modify Netinfor button to pop up the Network Parameter Modification interface. Figure 4-6 Modify Network Parameters Window Change the device IP address to the same subnet with your computer by either modifying the IP address manually. Input the password and click the OK button to change the device network information.
Video Access Control Terminal 5 Appendix: 5.1 Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
Video Access Control Terminal 5.2 Specification Model Camera Fingerprint Capacity DS-K1T500SF/DS-K1T500S 1080P, More than 2 Megapixel; Recognition Distance<= 1m; Support IR Light; Support Outdoor Operation; Support Scanning QR Code 3000 (DS-K1T500SF) Card Capacity 50,000 Recording Capacity 200,000 Authentication Speed 1: N Fingerprint Recognition Duration (Matching with All Fingerprints) <= 1s (DS-K1T500SF) FAR Fingerprint<= 0.001 %(DS-K1T500SF) FRR Fingerprint<= 0.
Video Access Control Terminal Tamper-Proof Working Temperature Working Humidity Appearance Mount Option Dimensions Support -40°C to 70°C 10% to 90% (No Condensation) Metal Wall Mounting; Metal Door Mounting Cuboid 0101001061114 14
Video Access Control Terminal 15
