Hanover Outdoor Furniture IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), PLEASE DO NOT RETURN TO THE RETAILER/STORE from where you purchased the product. Please call our Toll‐Free Customer Service Hotline at: 1‐800‐416‐3511 Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday Or visit our website at: www.hanover‐products.
Outdoor Furniture 1-Year Limited Warranty Program For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty revert back to the date of original purchase for future warranty.
Care & Maintenance Outdoor furniture can be enjoyed for many years when well maintained. Regular Maintenance Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air. For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution areas.
ASSEMBLY INSTRUCTIONS 1 Assemble furniture on a smooth, non-abrasive surface. Attach the back frame to right arm by using two 5/16"x40 mm bolts and washers as shown in Fig.1 . Guide the bolts through holes in back frame, into pre-drilled holes in the right arm . Hand tighten only. Attach the seat frame to right arm and back frame by using four 5/16"x25 mm bolts and washers as shown in Fig.2 . Hand tighten only.
ASSEMBLY INSTRUCTIONS CSA Model 98900 Printed in China DRC02200 Installer: Leave these instructions with consumer. Consumer: Keep these instructions for future reference. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information 3 Information about Propane 4 Specifications 4 Installation 5 Natural Gas Conversion 6 Lighting Instructions 8 Maintenance 8 Batteries 9 Parts List 9 Warranty 10 2
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS A self contained LP-gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device). See Figure 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
INSTALLATION 1. Carefully unpack all items from the box. Place the table in its final position. There must be a minimum of 24 inches of clearance from the side of the table top to any combustible walls. 2. With the help of another person, carefully place the natural stone table top onto the table base. After making any necessary adjustments to the alignment of the natural stone table top and the table base, use four bolts and washers as shown in Fig.3.
4. Lift off the tank door, place the tank in the holder and use the chain to hold the tank. Connect the regulator as shown in Fig. 5. Screw the black handle clock-wise to tighten. Turn the handle counterclock-wise to remove. The hose must point down. Open the control door and check that the valve is turned all the way clockwise to the “OFF” position. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection and to the valve-hose connection to check for leaks.
2. Disconnect the gas tube from the orifice and remove the orifice holder as shown in Fig .7. Figure 7 3. Replace the propane orifice (See Fig.8) with the natural gas orifice from the kit and reinstall the orifice holder by tightening the nuts as shown in Fig. 9. Reconnect and tighten the gas tube to the orifice. Figure 8 Figure 9 Apply a solution of soapy water to all connections to check for leaks. If soap bubbles continue to form, the connection has a leak.
LIGHTING INSTRUCTIONS 1. Locate the control and igniter panel. Make sure the control knob is in the “OFF” position. See Fig. 11. Open the tank door and open the tank valve all the way. 2. Push in the igniter button. You will hear a slight clicking sound. With the igniter button pushed in, push and turn the control knob to the “ON” position. The fire should light within a few seconds. Once the flame is lit, release the igniter button and continue to hold the control knob in for 10 to 15 seconds.
BATTERIES Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignition module located on the control panel to access the battery compartment. The ignition module requires one AAA size battery. See Fig. 13.
90-DAY LIMITED WARRANTY What is Covered Under This Warranty? The item you have purchased is warranted against defects in materials and workmanship for the following parts as outlined below only when unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: • Burner Assembly • Firepit Base • Firepit Top How Do I Obtain Warranty Service? To obtain warranty service, you must contact our customer service center within the rele
PARTS IDENTIFICATION LIST * NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE PARTS LIST DESCRIPTION ORDER PART # QTY A SEAT FRAME SG0154 1 B BACK FRAME SG0155 1 C LEFT ARM SG0156 1 D RIGHT ARM SG0157 1 E GLIDER BASE W/ GLIDER BRACKET SG0158 SG0159 1 F 5/16" X 25 MM BOLT HW0186 6 G 5/16" X 40 MM BOLT HW0275 8 H Ø8.5 X 1.5 MM WASHER HW0005 14 I BOLT COVER HW0105 14 J HEX BOLT DRIVER HW0006 1 GLIDER BRACKET G0080 ST4.