User's Manual Part 3

ManualsBrandsHanwha Techwin ManualsBaby MonitorsWireless Baby Monitor

· Overview

Getting to know your Monitoring system

Wireless Monitor

After opening the box, fully charge the monitor before use. After initial charge, recharge as needed.

Front Controls



Navigation Controls / Button

Viewing Mode: The following controls are used while watching live video from the camera:

• Press the [

] or [

] button to adjust camera’s framing upwards or downwards.

• Press the [

_] or [+] button to adjust camera’s framing to the left or right.

• Press [

] button to turn on/off the night light.

• While in zooming, use [$/%/_/+] button to move the screen around.

Menu Mode: Use the [$/%/_/+] button arrows to navigate in Menu Mode.

Press the [

] button to confirm the menu selection.

VerVIeW

Power LED

Indicator turns green when powered.

When battery is charging, this LED will in green color.

4.3” LCD Screen

Displays video from the camera.

Sound Level LEDs

Flashes when sound is detected.

MENU Button

Press to access from video monitor mode to menu

mode operation. In menu mode, press this button will go

back to monitor mode with save from selection.

SLEEP Button

Used to turn on / off the screen by press this button.

User can turn on the video again by pressing any buttons.

If camera is disconnected, monitor screen would be

turned on automatically in Sleep mode.

Monitor

Antenna

Receives and sends signals from

or to

the

camera.

Micr

ophone

When there are pairing between monitor and camera,

There is a function of transmission of

audio

only.

Navigation Controls

oK/Night light

Button

Used

navigate while in Menu

Mode.

Used for PTZ operation and Night Light while

Viewing

Mode.

Summary of content (9 pages)

PAGE 1
Overview Getting to know your Monitoring system Wireless Monitor After opening the box, fully charge the monitor before use. After initial charge, recharge as needed. Front Controls Monitor Antenna Receives and sends signals from or to the camera. Power LED Indicator turns green when powered. When battery is charging, this LED will in green color. Sound Level LEDs Flashes when sound is detected. 4.3” LCD Screen Displays video from the camera.
PAGE 2
Back Controls TALK Button Press down and hold the button to talk back to the camera. TALK Kick Stand Speaker Use to hold the monitor onto a table. Produces the sound transmitted from the camera(s). - ON - VOX - OFF 04 nn `` You must have more than one camera configured on the system when using the functions that requires more than one camera.
PAGE 3
Wireless Camera Front & Back Controls IR LEDs Infrared LED’s provide viewing in no / low light conditions. Microphone Receives sounds for the area near the camera, and transmits sound from the camera to the monitor. Speaker Produces the sound transmitted from the monitor. Night Light Button Turns Night Light ON or OFF. When the camera is powered on, Night Light would be automatically turned on. Camera Antenna Sends & receives signals to or from the monitor.
PAGE 4
Installation How to Install 1. 2. CAUTION: If you use the system to watch a young child, do not place the camera in the child's reach. Wireless Monitor 1. Place the monitor in a place that will have clear reception with your camera(s). 2. Pull out the stand. Carefully unpack the camera. If you are installing cameras that did not come with the system, please see the pairing camera section of this manual for details on installation. Mount the camera to the wall.
PAGE 5
Appendix Item Pan Angle Specifications Item Operating Frequency Range System General 2400 MHz~2483.5 MHz Transmitting Power 17dBm Max Type of Spread Spectrum TX FHSS Monitor Sensitivity Type of Modulation Data Rate Transmission range Details -88dBm GFSK 3Mbps Max 300m 300° Wireless Camera Tilt Angle 110° RoHS Compliance Yes for CE version only Regulation Compliance Audio Weight Details FCC/CE Built in Microphone/ Speaker 218g Wireless Monitor Display Type/Size Color TFT 4.
PAGE 6
Troubleshooting Problem No picture from a camera Solution 1. 2. 3. 4. 5. Check all connections to the camera. Make sure the adapter is plugged in. Make sure that the cameras and monitor are both ON. Make sure that the camera is in range of the monitor. Make sure the camera and monitor are paired. Adjust the monitor antenna to vertical position. The picture is or has become choppy The picture may become choppy when experiencing a lower frame rate (i.e. 10 frames per second vs.
PAGE 7
Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive. Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems.
PAGE 8
TEMPLATE This template is used to install the camera on the wall.
PAGE 9
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : 1-877-349-3149 www.samsungsv.com SAMSUNG TECHWIN EUROPE LTD.