ITEM #0698388, 0698389 SARATOGA CEILING FAN MODEL #00885, 00886 ETL MODEL #60-STG Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. Español p. 18 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-473-4537, 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday. AB15781 Lowes.
TABLE OF CONTENTS WARNING Safety Information............................................................................................................... 3 Package Contents............................................................................................................... 4 Hardware Contents............................................................................................................. 5 Preparation..................................................................................
HARDWARE CONTENTS (shown actual size) PACKAGE CONTENTS K F A AA CC L G B BB C M H D Wire Connector Qty. 4 Decorative Screw Qty. 15 Blade Arm Screw Qty. 11 DD R I E PART A B C D E F G H I J K L M J DESCRIPTION Mounting Bracket Canopy Canopy Cover Yoke Cover 6 in. Downrod Blade Arm Blade Fan Motor Assembly Fitter Plate Light Fitter Assembly Glass Bulb Remote Pack Blade Screw Qty.
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 4. Insert downrod (E) through canopy (B), canopy cover (C), and yoke cover (D). Thread wires from fan motor assembly through downrod (E). 1 1. Determine mounting method. A-Downrod Mount (standard or angled ceiling) B-Angle Mount (standard ceiling only) IMPORTANT: If angle mounting, check to make sure the ceiling angle is not steeper than 20˚. 4 E B A C D B 2.
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Note: BLACK wire is hot power for fan and light kit. WHITE wire is common for fan and light kit. GREEN wire is grounded wire. lf house wires are different colors than referred to above, stop immediately and consult a professional electrician to determine proper wiring. 7 10. Slide canopy cover (C) over two screws and rotate clockwise until it locks. Supply circuit White Black Black 8.
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 13. Loosen two preassembled screws from fan motor assembly (H). Remove and save remaining preassembled screw. 13 D H 16. Loosen two preassembled screws from fitter plate (I). Remove and save remaining preassembled screw. 16 screw Screw 14. Pull the BLUE and BLACK wires from fan motor assembly (H) through center hole of fitter plate (I). Align two keyslots on fitter plate (I) with two screws on black bracket below fan motor assembly (H). 14 H 17.
ASSEMBLY INSTRUCTIONS OPERATING INSTRUCTIONS 19. Install bulbs (L) into sockets. REMOTE CONTROL TRANSMITTER: Note: The receiver is already wired and built into the fan housing from the factory. Receiver assembly is not needed. “Tap” refers to pressing a button on the remote for less than one second. “Press and hold” refers to pressing a button and holding the button down for one second then release the button. 19 IMPORTANT NOTE: The fan has an energy-saving wattage limiter included.
OPERATING INSTRUCTIONS CARE AND MAINTENANCE • To reduce the risk of fire, electric shock or injury to persons, care and maintain this fan. 5. Fan On/Off (See Fig. 2): • Fan On/Off controls power to the fan. • When fan is on, tap “ ” key. Fan will turn off. • When fan is off, tap “ ” key. Fan will turn on. • When fan is off, tap “ ” key. fan has memory and turns fan to most recent fan speed. 6. Light On/Off/Dimming (See Fig. 2): • Tap “ ” key to turn light on/off; press and hold for dimming. 7.
WARRANTY TROUBLESHOOTING PROBLEM Fan blades do not move Noisy operation. POSSIBLE CAUSE 1. Power is off or fuse is blown. 2. Cracked blade. Excessive wobbling. 1. Blades are loose. 2. Unbalanced blades. 3. Fan not securely mounted. 4. Blade arms incorrectly attached. 5. Fan too close to vaulted ceiling. 1. No flash on Remote control transmitter LED. malfunction. 2. The remote control does not work. CORRECTIVE ACTION 1. Turn power on or check fuse. 2. Turn power off.