ITEM #0747607, 0747608, 0810513 SAGECOVE CEILING FAN MODEL #40840, 40841, 40677 Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. Español p. 22 ATTACH YOUR RECEIPT HERE Purchase Date _________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparation . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS D A G PART A B C D E F G H I J K L M N O P Q R S T U V W X Y H F M R J E C B I O N S T K L P U V Q W X Y DESCRIPTION Downrod Downrod Pin (preassembled to Downrod [A]) Downrod Clip (preassembled to Downrod [A]) Mounting Bracket (preassembled to Canopy [E]) Canopy Canopy Cover (preassembled to Canopy [E]) Motor Assembly Switch Housing (preassembled to Motor Assembly [G]) Switch Housing Cap (preassembled to Light Kit [J]) Light Kit Finial Cap (preassembled to Light K
HARDWARE CONTENTS (shown actual size) AA DD EE ar Blade Screw Qty. 15 + 1 extra Blade Washer Qty. 15 + 1 extra Plug Button Qty. 1 ze ze b o r Br e e H H ar Wire Connector Qty. 3 + 1 extra CC BB b o r Br e e Pull Chain Extension Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
SAFETY INFORMATION CAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are secured. PREPARATION Before beginning the assembly of this product, ensure that all parts are present.
INITIAL INSTALLATION 1. Turn off the circuit breakers and the wall switch to the fan supply line leads. 1 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Determine the mounting method to use. Standard mounting is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). 2 Angle-style mounting is best suited for angled or vaulted ceilings.
INITIAL INSTALLATION 4. Loosen all four preassembled mounting bracket screws (S), then completely remove the two mounting bracket screws (S) from the round holes of canopy (E). Set aside for later use. 4 D S Detach mounting bracket (D) from canopy (E). E 5. Attach mounting bracket (D) to outlet box (not included) using screws and washers provided with the outlet box. 5 D CAUTION: It is very important to use the proper hardware when installing the mounting bracket (D) as this will support the fan.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 1. Remove the downrod pin (B) and downrod clip (C) from the downrod (A). Then partially loosen the set screws (W) in the yoke at the top of the motor assembly (G). 1 A C Yoke B W G 2. Insert the downrod (A) through the canopy (E) and yoke cover (O). Feed the wires from the motor assembly (G) through the downrod (A). 2 E A O G 3.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 4. Depending on the length of downrod you use, you may need to cut the lead wires back to simplify the wiring. If you decide to cut back the lead wires, it is suggested you do so in the following manner: Take the lead wires and make sure you have pulled them all the way through the top of the downrod. Measure 8 inches of lead wire, then cut the excess wire off with wire cutters (not included). 5. If you decided to cut back the lead wire in Step 4, strip 1/2 in.
CLOSEMOUNT INSTRUCTIONS Helpful Hint: The downrod (A), canopy cover (F) and yoke cover (O) are not used in this type of installation. 1 1. Remove the canopy cover (F) from the bottom of the canopy (E). E F 2. Remove three Phillips-head closemount screws (V) from the top of the motor assembly (G). Align the canopy (E) with the holes in the top of the motor assembly (G), then re-install the Phillips-head closemount screws (V) to secure the canopy (E) to the top of the motor assembly (G). 2 V E G 3.
WIRING WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. 1.
FINAL INSTALLATION Note Closemount installation will not have the downrod (A), yoke cover (O) or canopy cover (F). 1. Align the canopy (E) over the loosened mounting 1 bracket screws (S) preassembled on mounting bracket (D). Place the keyholes of the canopy (E) S D onto the mounting bracket screws (S) and rotate the canopy (E) clockwise. E 2. Secure the canopy (E) with the mounting bracket screws (S) previously removed (Step 4, page 8). Tighten all mounting bracket screws (S) securely. 2 S E 3.
FINAL INSTALLATION 4. Install the blade arm (P) to the underside of the motor assembly (G) with motor screws (R) previously removed (Step 6, page 8). Tighten with Phillips screwdriver. 4 Repeat for each blade arm (P). G P R Note: If you wish to install the fan without the light kit (J), proceed to Step 8. 5 5. To install the light kit (J), first remove the three switch housing screws (X) from the switch housing cap (I).
FINAL INSTALLATION 7. Remove the preassembled finial (L), finial cap (K), hex nut (T) and rubber washer (U) from the light kit (J). Lift the glass bowl (N) onto the threaded rod at the bottom of the light kit (J). 7 Feed the pull chain coming from the grommet in the light kit (J) through the off-center hole in the glass bowl (N). Feed pull chain coming from the center of the light kit (J) through the center hole in the glass bowl (N). J N Secure glass bowl (N) with rubber washer (U) and hex nut (T).
FINAL INSTALLATION 10. Attach the pull chain extensions (BB) or custom pull chain extensions (not included) to the fan and light pull chains (if applicable). 10 Hardware Used b o r Br e e BB b o r Br e e H ar 11. Turn on power supply to the fan. 11 Assembly is complete.
OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. 1 The light pull chain has two positions to control the light, ON and OFF. Light Pull Chain 2. Use the fan reverse switch, located on the switch housing (H), to optimize your fan for seasonal performance.
CARE AND MAINTENANCE At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor assembly with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. Bulb Replacement: Use 60-watt max. candelabra-base bulbs or CFL equivalent. Important Shut off the main power supply before you begin any maintenance task. Do not use water or a damp cloth to clean the fan.
TROUBLESHOOTING PROBLEM There is excessive wobbling. POSSIBLE CAUSE 1. The blades and/or blade arms are loose. 2. The blades are unbalanced. 2. Switch one blade with a blade from the opposite side. Or balance the fan using the blade balancing kit (Y). 3. The fan mounting is not secure. 3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the electrical outlet box. The bracket must be flush without movement against the outlet box. 4.
LIFETIME LIMITED WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, excluding any glass or plastic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
