ITEM #0915543, 1133113 BUILDER’S SERIES CEILING FAN MODEL #41391, 41690 Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. b o r Br e e H ar ze H ar ze Español p. 18 b o r Br e e ATTACH YOUR RECEIPT HERE Purchase Date _________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparation . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS O B G A C D H L N E F M I J K PART A B C D E F G H I J K L M N O DESCRIPTION Motor Housing Upper Mounting Bracket Lower Mounting Bracket (preassembled to Motor [D]) Motor Switch Housing (preassembled to Motor [D]) Light Kit (preassembled to the Switch Housing [E]) Light Pan Bulb Glass Bowl Blade Arm Blade Lower Bracket Screw (preassembled to Lower Mounting Bracket [C]) Switch Housing Screws (preassembled to Light Pan [G]) Motor Screw (preassembled to Motor [D]) Motor Housing Scre
HARDWARE CONTENTS (shown actual size) DD CC Wire Connector Qty. 3 + 1 extra Blade Screw Qty. 15 + 1 extra b o r Br e e ar H H ar ze BB ze AA b o r Br e e Blade Washer Pull Chain Extension Qty. 15 + 1 extra Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
SAFETY INFORMATION CAUTION: Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are secured. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
INITIAL INSTALLATION 2. This fan is intended for Flushmount installation. Standard Mounting, Angle Mounting, and Closemount installations are not available. 3. Ensure the blades (K) will be at least 30 in. from any obstructions and will be at least 7 ft. above the floor. 2 Standard Mounting Angle Mounting Flushmount Closemount 3 K 30 in. Min 7 ft. Min 4. Secure the upper mounting bracket (B) to the outlet box (not included) using screws and washers provided with the outlet box.
INITIAL INSTALLATION 5. Remove the lower bracket screws (L) from underneath the lower mounting bracket (C). 5 C L 6. Place one tab of the lower mounting bracket (C) into a slot in the upper mounting bracket (B), then slide the second tab of the lower mounting bracket (C) into the second slot on the upper mounting bracket (B) until all four holes are in alignment. 6 B Slot C 7.
WIRING WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12 gauges and/or there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a Ground (Green or Bare) wire is present. 1.
FINAL INSTALLATION 1. Temporarily lift the motor housing (A) to the upper mounting bracket (B) to determine which two motor housing screws (O) preassembled in the sides of the upper mounting bracket (B) align with the slotted holes in the top edge of the motor housing (A). Partially loosen the two motor housing screws (O) that align with the slotted holes. 1 B O Remove the other two motor housing screws (O) from the upper mounting bracket (B). A 2.
FINAL INSTALLATION 4. Partially insert the blade screws (BB) along with the blade washers (CC) through the blade (K) and into the blade arm (J). Tighten each blade screw (BB) with a Phillips screwdriver, starting with the one in the middle. Repeat this step for the remaining blades (K) and blade arms (J). 4 BB CC Hardware Used BB Blade Screw x 15 CC Blade Washer x 15 5. Install the blade arm (J) to the underside of the motor (D) with motor screws (N) previously removed (Step 3, page 10).
FINAL INSTALLATION 7. Install the bulb (H) into the socket of the light kit (F). 7 F H 8. Lift the glass bowl (I) into the light pan (G) and twist in a clockwise direction until the glass bowl (I) is secure. 8 G I 9. Attach the pull chain extensions (DD) or custom pull chain extensions (not included) to the fan and light pull chains. 9 Note When facing the reverse switch, the pull chain for the fan is on the right and the pull chain for the light is on the left.
OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. 1 ar b o r Br e e Fan Pull Chain Light Pull Chain 2. Use the fan reverse switch, located on the switch housing (E), to optimize your fan for seasonal performance. ze b o r Br e e H H ar ze The light pull chain has two positions to control the light, ON and OFF.
CARE AND MAINTENANCE At least twice each year, lower the motorhousing and tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection. Bulb Replacement: Use 60-watt max. E26-base LED, CFL or incandescent bulbs. Halogen bulbs are not recommended for this item.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 1. The blades and/or blade arms 1. Check and tighten all screws that are loose. hold the fan blades to the blade arms and the blade arms to the motor. 2. The blades are unbalanced. There is excessive wobbling. The fan operates correctly, but the lights are not working. 3. The fan mounting is not secure. 1. The bulbs are not installed correctly. 2. The light kit wire plugs are not connected properly. 3. There is a faulty wire connection. 15 2.
LIMITED LIFETIME WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, excluding any glass or plastic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
