ITEM #3415246 KENTON CEILING FAN MODEL #HTD20005-BK Harbor Breeze® and logo design are Español p. 18 trademarks or registered trademarks of LF, LLC. All rights reserved. ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com.
TABLE OF CONTENTS Package Contents ............................................................................................................ 3 Hardware Contents ...................................................................................... ................... 4 Safety Information ............................................................................................................ 4 Preparation ...........................................................................................
PACKAGE CONTENTS C A G K D I E B CR2032 3V X6 X2 H F J PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY A Ceiling Plate 1 H Trim Ring [Preassembled on Motor Assembly (B)] 1 B Motor Assembly 1 I Mounting Screw [Preassembled on Motor Assembly (B )] 4 J Mounting Plate Screw [Preassembled on Motor Assembly (B )] 3 K Switch Housing Screw [Preassembled on Switch Housing (C )] 3 C Switch Housing 1 D Blade 3 E Light Kit 1 F Bowl 1 G Remote Unit 1 3
HARDWARE CONTENTS (not shown actual size) AA Blade Screw Qty 12+1 extra SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate or install the product. . All electrical connections must comply with local codes, ordinances or the National Electric Code (NEC). Contact your municipal building department to inquire about your local codes, permits and/or inspections. .
WARNING Chemical Burn Hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children.
INITIAL INSTALLATION INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fan supply line leads. 1 T Turn Off Power Source DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. or 2. . Fan mounting option: 2 This fan was designed to be mounted only on flat ceilings and can be used on ceilings less than 9 feet high (blades should be a minimum of 7 feet from the floor.
INITIAL INSTALLATION INSTRUCTIONS 4. Partially remove two diagonal mounting screws (I) on the round holes, keep for later use. And loosen the other two screws (I). 4 I B 5. Hang the motor assembly (B) onto the hook from the ceiling plate (A). This will allow for hands-free wiring.
WIRING INSTRUCTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. WARNING: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. WARNING: If house wires are different colors than referred to in the following steps, stop immediately. A professional electrician is recommended to determine proper wiring.
FINAL INSTALLATION INSTRUCTIONS 1. After wire connections, take the motor assembly (B) off the hook.Raise the motor assembly (B) up to the ceiling plate (A).Align two remained screws (I) on the motor assembly (B) to the keyholes on the ceiling plate (A), rotate clockwise until the screw heads engage the keyhole slots fully. Make sure not to break any wire connections. 1 A I B 2. Re-install two mounting screws (I) to the round holes, securely tighten four (4) mounting screws (I). 2 A I 3.
FINAL INSTALLATION INSTRUCTIONS 4. Insert blade (D) through slot on fan motor assembly (B), align with four screws holes, securely tighten with blade screws (AA). Repeat for remaining blades. 4 B Hardware Used AA Blade Screw x 12 5. Remove one of the mounting screws (J) on the mounting plate of motor assembly (B) and keep for later use. And loosen the other two. AA D 5 B Mounting Plate J 6. Insert the 9 pin connector from the motor assembly (B) through the center hole in the switch housing (C).
FINAL INSTALLATION INSTRUCTIONS 7. Remove three (3) screws (K) preassembled on the switch housing (C). Attach the connector from the light kit (E) to the connector from the motor assembly(B). Align the three holes between the light kit (E) and the switch housing (C). Re-install the switch housing screws (K) to attach the light kit (E) to the switch housing (C). Tighten all mounting screws (K) securely. NOTE: The two connectors have keyholes that must be mated correctly before they can be engaged.
OPERATION INSTRUCTIONS 2 3 NOTE: ON DIM NOTE: Each transmitter of this remote control carries a unique ID code to facilitate communication between paired devices. The ID code is set by factory and is not user changeable. However, you will be required to perform an “ID code learning ” process manually under these circumstances: • If you have multiple fans installed within a close proximity and want to control all fans using a same remote transmitter. NOTE: Each fan requires its own receiver.
OPERATING INSTRUCTIONS 5. The buttons on the remote control the fan speed and light as follows: 5 1 2 3 Fan ON/OFF 4 5 Brightness 25% 6 Brightness 50% 7 Brightness 75% 8 Brightness 100% 9 Light Dimmer switch: a.) on “DIM”: with dimmer function. b.) on “ON” : without dimmer function Note: Factory set is on “DIM” position. If the light is not dimmable, slide it to “ON” position, otherwise it may cause the light to flicker.
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION 1. Set screws are loose. 2. Using non-approved speed control. 3. Normal noise. Fan sounds noisy 4. Wire connectors inside switch housing rattling. 5. Cracked blade. 6. The distance from canopy to ceiling is too great. 7. Glass is not secure. 1. Hanger bracket and/or ceiling outlet box is not securely fastened. 2. Set screw in downrod assembly is loose. 3. Fan hanger ball is not properly seated in canopy tabs. 4.
LIMITED LIFETIME WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and material present at time of shipment from the factory for life (with limitations) from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge or, at our option, replace the ceiling fan with a comparable or superior model. To obtain warranty service, present a copy of your sales receipt as proof of purchase.
FCC WARNING This device (including remote control and LED module) complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
REPLACEMENT PART LIST For replacement parts, call our customer service department at 888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com.