NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Table of Contents Safetye�������������������������������������������������2 Specifications......................................5 Setup...................................................6 Operationa�������������������������������������������10 Maintenancei��������������������������������������12 Parts List and Diagram.......................14 Warranty..............................
NOTICE Personal Safety b. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair increases the risk of injury to persons as a result of being caught in moving parts. c. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. d. e. Use safety equipment.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Air Source a. Setup Never connect to an air source b. Never use oxygen, carbon dioxide, that is capable of exceeding combustible gases or any bottled 200 psi. Over pressurizing the gas as an air source for the tool. tool may cause bursting, Such gases are capable of explosion abnormal operation, breakage of and serious injury to persons. the tool or serious injury to persons.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. 4. Read all of the information concerning coating products and cleaning solvents. Do not use chlorinated solvents (e.g. 1‑1‑1 trichloroethylene and dichloromethane, also known as methylene chloride) to clean spray guns. Many spray guns contain aluminum, which reacts strongly to chlorinated solvents.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Initial Setup Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Before Setup Setup 1.
NOTICE 6. Adjust the air compressor’s output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool’s maximum air pressure at any time. Adjust the pressure gradually, while checking the air output gauge to set the right pressure range. 8. If the tool will not be used at this time, turn off and detach the air supply and safely discharge any residual air pressure to prevent accidental operation.
For technical questions, please call 1-800-444-3353. D E F G H C F E Function F G I I J Filter Description J H L Coupler and Plug J Regulator K Lubricator* I N K M Leader Hose* N Air Cleaner / Dryer* O Air Adjusting Valve* *Optional components. Non-lubricated Tools C C For noise and vibration reduction Secures air compressor in place Isolates sections of system Ball Valve for maintenance Isolation Hose For vibration reduction Main Air Line - 3/4″ min.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Setup Safety Components and Controls Hopper Lock Nut Operation Fluid Control Knob Clamp Nozzle Air Inlet Trigger Maintenance Trigger Lock Figure C Item 66103 For technical questions, please call 1-800-444-3353.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Workpiece and Work Area Set Up Setup 1.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. 7. Adjust the mixture, if necessary, according to the coating manufacturer’s directions. 8. If the coating is the proper consistency, but is still not spraying properly, adjustments may be made by: a. Adjusting Air Pressure. b. Adjusting Fluid Control Knob. c. Changing the Nozzle. Safety 6. Test the consistency by spraying on a piece of scrap material. Fluid Adjustment 9.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY: Detach the air supply and safely discharge any residual air pressure in the tool before performing any inspection, maintenance, or cleaning procedures.
NOTICE 7. Use appropriate solvent (see Solvent Selection, left) to wipe down Spray Gun body. 8. Lubricate Spray Gun after cleaning. A non‑silicon oil or a light lubricant may be used on threaded connections before storing. Solution Disposal After cleaning, dispose of cleaning solution according to the solution manufacturer’s directions and local hazardous waste standards. Safety Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Safety Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY Setup THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. 19 8 9 10 11 Setup 7 2c 1 Safety Assembly Diagram 3 2b 4 5 6 20 2a 17 14 18 16 Operation 12 13 15 Maintenance 21 Item 66103 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.