User guide

37
OPERATION
Now that you have installed your system components and completed at
l
east a basic configuration of your receiver, you are ready to begin
enjoying your home theater system.
Turning On the AVR 247
Gently press the Master Power Switch until the word OFF is no longer visi-
ble. The Power Indicator above the two power switches should light up in
amber. This indicates that the AVR is in Standby mode and is ready to be
turned on. Normally, you may leave the Master Power Switch in the ON
position, even when the receiver is not being used. See Figure 58.
Figure 58 – Power Switches
There are several ways in which the AVR 247 may be turned on:
a) Press the Standby/On Switch on the front panel. See Figure 58.
b) Press the Source Select Button on the front panel. See Figure 59.
Figure 59 – Source Select Button
c) Using the remote, press any one of these buttons: AVR, DVD/CD,
TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, VID4, XM,
AM/FM, 6/8CH. See Figure 60.
Figure 60 – AVR and Input Selectors
NOTE: Any time you press one of the remote’s Input Selectors
(i.e., DVD/CD, TAPE/The Bridge, XM, VID1, VID2, VID3, VID4 or
HDMI 1/HDMI 2), the remote will switch modes so that it will
only operate that device. To control the receiver, press the AVR
Button to return the remote to AVR mode.
To turn the receiver off, press either the Standby/On Switch on the front
panel, or press the AVR Button and the OFF Button on the remote.
Unless the receiver will not be used for an extended period of time (for
example, if you will be on vacation), it is not necessary to turn off the
Master Power Switch. When the Master Power Switch is turned off, any
settings you have programmed, including system configuration and
preset radio stations, will be preserved for up to four weeks.
Sleep Timer
You may program the AVR to play for up to 90 minutes and then turn
off automatically using the sleep timer.
Press the Sleep Button on the remote, and the time until turn-off will be
displayed. See Figure 61. Each additional press of the Sleep Button will
reduce the time until turn-off by 10 minutes, until the OFF setting is
reached, which disables the sleep timer.
Figure 61 – Sleep Button
When the sleep timer has been set, the front-panel display will automati-
cally dim to half-brightness. If you press any button on the remote or
front panel, the display will return to full-brightness. The display will dim
again several seconds after your last command.
If you press the Sleep Button after the timer has been set, the remaining
time until turn-off will be displayed. You may press the Sleep Button to
change the time until turn-off. Pressing and holding the Sleep Button will
disable the sleep timer, and the SLEEP OFF message will appear.
Volume Control
The volume may be adjusted either by turning the knob on the front
panel (clockwise to increase volume or counterclockwise to decrease
volume), or by pressing the Volume Control Buttons on the remote.
See Figure 62. The volume is displayed as a negative number of
decibels (dB) below the 0dB reference point, and may be changed
in 0.5dB increments.
Unlike the volume controls on some other products, 0dB is the maximum
volume for the AVR 247. Although it’s physically possible to turn the
volume to a higher level,
doing so may damage your hearing and your
speakers. For certain more dynamic audio materials, even 0dB may be
too high,
allowing for damage to equipment.
Figure 62 – Volume Controls
The
A
VR 247 is designed to reproduce audio with a minimum amount
of distortion,
which may lead you to think that your hearing and the
equipment can handle higher volumes. We urge caution with regard to
volume levels
.
Mute Function
To temporarily mute all speakers and the headphones, press the Mute
Button on the remote
.
See Figure 63.
Any recording in progress will not
be affected.
The MUTE message will flash in the display as a reminder
.