Assembly Instructions

ManualsBrandsHarriet Bee ManualsBaby & KidsDufault Glider Cradle

MADE IN CHINA

ASSEMBLY INSTRUCTIONS

Adult assembly required

Small parts may present choking hazard prior to assembly.

Enclosed please find simple step-by-step instructions to help you

quickly assemble your products. Before you begin we recommend

that you following the steps below:

1. Please read the instructions thoroughly.

2. Identify all parts and hardware.

3. You will need the following tools:

Philips head screw drive

Flat head screw drive

Hammer

DO NOT use power drills or drivers

To protect your parts during assembly please place them on a soft

surface.

To clean surface use only water on a damp cloth. DO NOT use

window cleaners or cleaning abrasives as it will scratch the surface

and could damage the protective co

ating.

Summary of content (8 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS Adult assembly required Small parts may present choking hazard prior to assembly. Enclosed please find simple step-by-step instructions to help you quickly assemble your products. Before you begin we recommend that you following the steps below: 1. Please read the instructions thoroughly. 2. Identify all parts and hardware. 3.
PAGE 2
WARNING .Failure to follow these warnings and the assembly instructions could result in serious injury or death. .Read all instructions before assembling cradle.KEEP INSTRUCTIONS FOR FUTURE USE. .Periodically check the safety of your cradle, by making certain all scerws,nuts and bolts are tightened securely and insepect cradle for damaged hardware, loose joints,missing parts or sharp edges. DO NOT use the cradle if any parts are missing or broken.
PAGE 3
HARDWARE AND TOOLS DIAGRAM a:Bearing (8pcs) b: Allen head bolts 2-3/8”(8pcs) g:Screws (4pcs) m:Flat washer n:Screw (16pcs) (2pcs) c:Wood dowels (4pcs) h:Nuts (4pcs) d:Barrel nuts (8pcs) i: Casters (2pcs) p:Allen key(for b&e) q:Allen key(for a) (1pc) (1pc) e: Allen head bolts 1-3/5”(8pcs) j: Casters with lock k: Spring washer (2pcs) (8pcs) r:Wrench (1pc) PARTS LIST E: Middle bar (1PC) F: Side bar (2PCS) G: Right Headboard (1PC) 3
PAGE 4
H:Left Headboard (1PC) J: Cradle base supports (2PCS) I: Rails (2PCS) K:Mattress support(1PC) L: Pad (1PC) STEP 1 Connect the base supporter (A) and the wood pins (C) and (D) (a) using the allen key (q) and wrench(r). The same way to assemble another piece of the base support with the wood pin(B) and (C).
PAGE 5
STEP 2 Connect the midlle bar (E),side bars (F) by inserting the allen head bolts (b), barrel nuts (d), and wood dowels (c) with the allen key (p). D STEP 3 Connect middle bar(E) and side bars (F) to the wood pin (B) and (C) by using the allen head bolts (b),barrel nuts(d), and wood dowels (c).
PAGE 6
Step 4 Connect the headboard (G) to the wood pins (C) and (D) with the bearings (a) by using allen key (q) and the wrench(r) q ak m q A a km F q a km Step 5 Release the Swing lock (f),and insert (f) through the holes on the headboard (H), and tighten the bolt. Connect the headboard (H) to the wood pins (C) and (B) with the bearings (a) by using the allen key(q) and wrench(r).
PAGE 7
Step 6 Connect the side rail (I) to the headboard (G) and (H) with the allen head bolts(e) by using the allen key (p). p Step 7 Connect the side rail (I) to the headboard (G) and (H) with the allen head bolts(e) by using the allen key (p).
PAGE 8
Step 8 1.Insert the four casters (j&i) with screw (g) and nuts(h) as shown,and tighten the bolts. 2.Assembled the cradle base supporters (J) to the mattress support (K). 3.Assembled the mattress support (K) to the to the assembled parts of STEP 7 by using screw (n).Tighten all by phillips-head screwdriver. n n i A A Step 9 i Put the mattress (L) on the mattress support.