Assembly Sheet

ManualsBrandsHarriet Bee ManualsBaby & KidsBearcreek Changing Table Dresser

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.

If you have any questions or missing parts, please contact us. DO NOT return product

parts to the store where it was purchased before contacting our Customer Service.

Changing Table

Summary of content (16 pages)

PAGE 1
Changing Table THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. If you have any questions or missing parts, please contact us. DO NOT return product parts to the store where it was purchased before contacting our Customer Service.
PAGE 2
WARNING: READ ALL WARNING & SAFETY INSTRUCTIONS BEFORE ASSEMBLING PRODUCT. KEEP INSTRUCTIONS FOR FUTURE USE. Storage: The product must be kept in a dry and clean area. Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be sure to use only a non-toxic finish specified for children’s products.
PAGE 3
Changer Parts Identification Sheet DO NOT assemble changer if parts and hardware are defective or missing. Contact us for exchange or keep the original box for return authorization. ~ Changer Assembly Parts A. Left Side Panel (1 pc) B. Right Side Panel (1 pc) C. Drawer Front Panels (2 pcs) D. Drawer Left Panels (2 pcs) E. Drawer Right Panels (2 pcs) F. Drawer Back Panels (2 pcs) G. Drawer Bottom Panels (2 pcs) H. Top Front Panel (1 pc) I. Top Back Panel (1 pc) J. Top Side Panels (2 pcs) K.
PAGE 4
~ Changer Assembly Hardware Item # Fittings Qty 1. Bolt 1/4” x 2-1/2” (14 pcs) 2. Bolt 1/4” x 2-1/4” (6 pcs) 3. Bolt 1/4” x 2-1/4” (4 pcs) 4. Bolt 1/4" x 1-3/4” (1 pc) 5. Barrel Nut 1/4” x 15 mm (14 pcs) 6. Barrel Nut 1/4” x 13 mm (11 pcs) 7. Dowel 8mm x 30 mm (17 pcs) 8. Screw F4 x 25 mm (20 pcs) 9. Machine Screw 3/16” x 1” (6 pcs) 10. Knob (4 pcs) (4 pcs) 11. Bolt 5/32” x 3/4" 12.
PAGE 5
Changer Parts Diagram Please follow this Parts Diagram to make sure that all parts are assembled in the correct position. C. Drawer Front Panel (1 pc) D. Drawer Left Panel (1 pc) E. Drawer Right Panel (1 pc) F. Drawer Back Panel (1 pc) G. Drawer Bottom Panel (1 pc) 10. Knobs (2 pcs) V. Drawer Support (1 pc) ~ Changer Top J I K H J M L H. Top Front Panel (1 pc) I. Top Back Panel (1 pc) J. Top Side Panels (2 pcs) K. Top Panel (1 pc) L. Upper Front Rail (1 pc) M.
PAGE 6
Changer Parts Diagram Please follow this Parts Diagram to make sure that all parts are assembled in the correct position. ~ Changer Unit R A U O N S B T P P Q A. Left Side Panel (1 pc) B. Right Side Panel (1 pc) N. Front Shelf Rail (1 pc) O. Back Shelf Rail (1 pc) P. Front Drawer Rails (2 pcs) Q. Back Drawer Rail (1 pc) R. Upper Back Panel (1 pc) S. Shelf (1 pc) T. Lower Back Panel (1 pc) U.
PAGE 7
Changer Drawer Assembly Sheet STEP 1: Attach Drawer Left Side Panel (D) and Drawer Right Side Panel (E) to Drawer Front Panel (C) with 4 screws (#8). C 8 D 8 8 E STEP 2: Slide Drawer Bottom Panel (G) into the grooves of the side panels.
PAGE 8
Changer Drawer Assembly Sheet STEP 3: Attach Drawer Back Panel (F) to side panels with 4 screws (#8). Make sure all screws are tightly secured. STEP 4: Attach Knobs (#10) to Drawer Front Panel with 2 Bolts (#11). 11 11 10 10 Repeat above steps to assemble the other drawer.
PAGE 9
Changer Top Assembly Sheet STEP 1: a. Insert 8 Dowels (#7) into top and bottom holes on each end of both Top Front Panel (H) and Top Back Panel (I). b. Attach 2 Top Side Panels (J) to Top Front Panel (H) and Top Back Panel (I) by using 4 Barrel Nuts (#6) of each corner of top panels before inserting 4 Bolts (#3). Warning labels must be UPRIGHT and facing INWARD. Tighten firmly with Wrench (#12).
PAGE 10
Changer Top Assembly Sheet STEP 3: Turn the changer top bottom side up, and then attach Upper Front Rail (L) and Upper Back Rail (M) to Top Panel with 6 Bolts (#9). Tighten firmly with Phillips Head Screwdriver (Not included).
PAGE 11
Changer Assembly Sheet STEP 1: Note: For easier assembly, place Left Side Panel (A) flat on the ground. a. Insert 3 Dowels (#7) into top holes on each end of Front Shelf Rail (N) and Front Drawer Rails (P). b.
PAGE 12
Changer Assembly Sheet STEP 3: a. Insert 3 Dowels (#7) into top holes on ends of Front Shelf Rail and Front Drawer Rails. b. Attach Right Side Panel (B) to unit by using 5 Barrel Nuts (#5) on the underside of right side of all rails before inserting 5 Bolts (#1). Tighten firmly with Wrench (#12). B 5 5 1 7 5 12 5 1 7 7 5 1 1 1 STEP 4: a. Insert Dowel (#7) into Shelf Divider (U). b. Attach Shelf Divider to Upper Back Panel by using a Barrel Nut (#6) before inserting Bolt (#4).
PAGE 13
Changer Assembly Sheet STEP 5: Insert Dowels (#7) into Shelf Divider (U) before attaching changer top to the unit. 7 7 U STEP 6: a. Secure changer top by using Barrel Nuts (#5) before inserting Bolts (#1). Tighten firmly with Wrench (#12). b. Gently rock one side of unit and test for uneven assembly. Retighten screws or reassemble entire unit if necessary.
PAGE 14
Changer Assembly Sheet STEP 7: Slide the drawers inside the changer. Changing Table Complete.
PAGE 15
Wall Safety Strap • TOOLS NECESSARY: RUBBER MALLET, PHILLIPS SCREW DRIVER. WARNING: WHEN UPRIGHT, IT IS POSSIBLE THAT THE FURNITURE MAY TIP OVER. FOR YOUR CHILD’S SAFETY, PLEASE INSTALL THE SAFETY WALL STRAP BEHIND THE FURNITURE. PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, PLEASE EMAIL US OR VISIT OUR WEBSITE. Safety Wall Strap 8” x 1.
PAGE 16
One year limited warranty We want you to be satisfied with any product that bears our name or logo. We will provide promptly, at the request of the retailer, and without charge, any missing parts that have been reported, with proper description, within 7 days of the purchase of the products. Our warranty guarantees optimal workmanship and lack of significant defects. The product warranty lasts a year from the date of your purchase.