Installation & Assembly

A: Left head board (1PC)
B: Right head board (1PC)
C: Rail (2Pcs)
E: Mattress board (1PC)
D: Stabilizer bar (1PC)
F: Mattress (1PC)
a: 2-1/8” Allen head bolt
(10 pcs)
d: 1-1/2” Wood dowel (2 pcs)
b:Barrel nuts (10 pcs)
c:
2” Allen wrench (1 pc)
e:
Castors (2 pcs)
f: Castors (2 pcs)
****Keep instructions for futher use****
.This product meets or exceeds specifications as issued by the consumer product safety for non-full size baby cribs.
.In gaps between a mattress too small or too thick and product sides.
.On soft bedding never add a mattress, pillow,comforter,or padding.
****Infants can suffocate****
.Use up and middle level mattress support only for a new born baby and not more than the first 3 months.
.Failure to follow these warnings and the instructions could result in serious injury or death.
.Caution:Before using this unit recheck all screws to be sure they are tightened securely. a periodic check should be
made of all screws&nuts to be sure they remain tight.
.Do not use plastic shipping bag or other plastic film as mattress covers not sold and intended for that purpose, they
can cause suffocation.
.
.
Never use a watter mattress with this product, if refinishing,use a non-toxic finish specified for children’s products.
Strings can cause strangulation! Never place items with a string around a child’s neck,such as hood strings or
pacifier cords.Never suspend strings over product or attach strings to toys.
.Discontinue use of the product when child is able to climb out or reaches the height of 35in.(890mm).
.When child is able to pull to standing position,set mattress/base to lowest adjustment position and remove bumper
pads, large toys ,and other objects that could serve as steps for climbing out.
.Never place product near window where cords from blinds or drapes can strangle a child.
.Always provide the supervision for continued safety of your child.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
.Never use this product if there are any loose or missing fasteners, loose joints,broken parts, or torn mesh/fabric.
check before assembly and periodically during use.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Always provide the supervision necessary for the continued safty of your child,when used for
playing. never leave child unattached
WARNING
WARNING
WARNING
Follow bellow to fold the crib:
1.take out the mattress (F)
2.take out the mattress board (E)
3.unlock the latch on the headboard
4.fold the crib
Assemble latch (i & j) to the headboard (A & B)
by using 5/8” screw (k).Then assemble plastic
block(n) to the headboard ( A & B) by using 3/4”
screw (m).Tighten all by phillips-head screwdriver.
Make sure that the latch on the bottom of each
headboard ( A & B ) are locked.
THEN FULLY tighten all the bolts.
STEP 1
STEP 4
STEP 5
STEP 6
B
A
A
B
C
D
C
B
e
f
A
A
B
B
E
A
Connect rail (C) and stabilizer bar (D)to the headboard ( A & B)
by screws (a) and nuts (b),wood dowel (d), washer (g), washer (h).
DO NOT fully tighten the bolts.
Connect rail (C) to the headboard (A & B) by screws
(a), nuts (b), washer (g) and washer (h).
STEP 2
STEP 3
a
a
c
a
a
a
a
b
b
b
b
b
a
a
a
a
d
b
Slot in the metal pin into the notch of left and right
headboard side corner post.then move up and down
to adjust the mattress base into highest level.
Assemble castors (e&f ) to the leg bottoms on the leg
on headboard (A&B).2 castors (e) with brake are in
the front.THEN add the mattress(F).
Select the desire level,and use both hand to lift up
the mattress base,then adjust the level to your
require height of the 2 level.
CAUTION:ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 23-5/8”(600MM) BY 37-3/4”
(959MM) WITH A THICKNESS NOT EXCEEDING 2” (51MM) . THE CRIB CONFORMS TO
APPLICABLE REGULATIONS PROMULGATED BY THE CONSUMER PRODUCTS SAFETY
COMMISSION.
b
b
b
g: Washer
(10 pcs)
h: Washer
(10 pcs)
i: Latch 1 (2 pcs)
n: Plastic block (2 pcs)
j: Latch 2 (2 pcs)
m: 3/4”screw
(4 pcs)
k: 5/8” screw
(6 pcs)
g
h
g
h
g
h
g
h
g
h
g
h
g
h
g
h
g
h
g
h
FLAT HEAD SCREWDRIVER
WRENCH
FLAT HEAD SCREWDRIVER AND
WRENCH REQUIRED FOR
ASSEMBLY----NOT INCLUDED
FLAT HEAD SCREWDRIVER
WRENCH
FLAT HEAD SCREWDRIVER AND
WRENCH REQUIRED FOR
ASSEMBLY----NOT INCLUDED
f
k
k
k
j
i
B
A
m
m
n
CONSUMER
PRODUCT
SAFETY
COMMISSION
AN INDEPENDENT TESTING
LABORATORY VALIDATES THE
MANUFACTURER’S CERTIFICATION
OF THIS CRIB TO ASTM F-406,
CPSC 16 CFR 1220
CERTIFIED
①
②
①
②