User Manual

ManualsBrandsHayward ManualsParts & AccessoriesHayward SP0710XR50 Pro-Series Vari-Flo Backwash Valve Coupling

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 1

VariFlo

Multiport

1 1/2” Filter Control Valve

Owner’s Manual

Model: SP0710XR50 (DE Filters)

TURN OFF PUMP BEFORE CHANGING VALVE POSITION

FUNCTIONS OF VALVE POSITIONS

VALVE SETTING

FLOW DIRECTION THROUGH VALVE

FILTER

PUMP - BOTTOM - THROUGH FILTER - TOP - RETURN

For normal filtration and vacuuming pool through

filter.

BACKWASH

PUMP - TOP - THROUGH FILTER - BOTTOM - WASTE

For cleaning filter.

RINSE

PUMP - BOTTOM - THROUGH VALVE - WASTE

For initial start-up and clearing valve of debris after

backwashing.

WASTE

PUMP – THROUGH VALVE - WASTE

For vacuuming directly to waste, lowering pool level

and/or draining pool.

CLOSED

NO CIRCULATION PAST PUMP POR

For shutting off all flow to filter and pool.

RECIRCULATE

PUMP – THROUGH

ALVE - RETURN

For bypassing filter, but circulating pool water.

WINTERIZING:

Drain and winterize filter and pump per manufacturer's

instructions. To drain water from VariFlo® Multiport

valve—depress and rotate valve handle and place

handle

ointer between an

detente

ositions.

CAUTION –Spring

Hazard – Release of

Valve spring

compression can

cause personal injury.

To avoid, only remove

handle pin if servicing

key O-ring. Remove

handle pin before

slowly removing Cover

screws in an alternate

pattern.

REF

NO.

PART NUMBER DESCRIPTION

NO.

REQ’D

1SPX0710X

Handle, Standard 1

2 SPX0710XZ7 Pin, for Handle 1

3 SPX0710Z16 Non-Metallic Bearin

(Pack of 5) 1

SPX0710G Valve Position Label 1

4SPX0710Z1

Cover screw set with nuts (Set of 6) 1

5SPX0710

Z5 Cover O-rin

6SPX0603SSprin

7 SPX0710Z62 Spring Washer Set (Set of 2) 1

8SPX0735G

O-ring & TFE Shaft seal set 1

SPX0710

¼” Plastic Pipe Plu

9 SPX0710XD Valve Seat Gasket 1

10 SPX0710xC Key 1

11 SX200Z4PAK2 Valve O-rin

(Set of 2) 1

SPX0710BA17 Key, Cover and Handle Assy 1

12 SPX0710M

Sight Glass with Gasket 1

SX200Z9 Gasket for Sight Glass 1

SPX0710XR50A

Valve body with gasket and pipin

GENERAL

1. Proper fitting make-up is hand tight plus one to 1-

1/2 turns maximum. Always use Teflon pipe tape

or Permatex No.2 for connections to provide a

good, "living" seal.

IMPORTANT: Do not over tighten pipe fittings.

2. SERVICING VALVE: If it becomes necessary to

service or gain access to the key or valve seat

gasket:

a. Set handle in “Winterizing” position.

b. Remove cover screws.

c. Lift cover and key assembly out.

3. RE-ASSEMBLY VALVE:

a. Wipe debris from cover 0-ring.

b. Set handle in a “Winterizing” position. Align

flat edge on cover with body. Press down to

seat assembly.

c. Secure assembly to body with cover screws

and nuts. Tighten cover screws evenly and

alternately.

Do not over tighten.

WARNING

ow a

nstruct

ons in this owner’s manual and on the equipment.

Failure to follow instructions can cause severe injury and/or death.

Hayward Pool Products

620 Division Street, Elizabeth, NJ 07207

Phone: (908) 355-7995

WWW.HAYWARD.COM

IS0710XR50 REV B

Summary of content (4 pages)

PAGE 1
IS0710XR50 REV B VariFlo® Multiport 1 1/2” Filter Control Valve Owner’s Manual Model: SP0710XR50 (DE Filters) TURN OFF PUMP BEFORE CHANGING VALVE POSITION GENERAL 1. Proper fitting make-up is hand tight plus one to 11/2 turns maximum. Always use Teflon pipe tape or Permatex No.2 for connections to provide a good, "living" seal. IMPORTANT: Do not over tighten pipe fittings. 2. SERVICING VALVE: If it becomes necessary to service or gain access to the key or valve seat gasket: a.
PAGE 2
Basic safety precautions shoulld always be followed, f inclu uding the follo owing: Failuree to follow instructions can cause seve ere injury and/or death. This is the e safety-alert symbol. s When n you see this symbol on yo our equipment or in this ma anual, look for one of the follow wing signal wo ords and be alert a to the pottential for perrsonal injury.
PAGE 3
WARNING – Risk of Electric Shock Failure to ground all electrical equipment can cause serious or fatal electrical shock hazard. Electrical ground all electrical equipment before connecting to electrical power supply. Failure to bond all electrical equipment to pool structure will increase risk for electrocution and could result in injury or death. To reduce the risk of electric shock, see installation instructions and consult a professional electrician on how to bond all electrical equipment.
PAGE 4
PRODUCTT REGISTRA ATION (Retain For Your Record ds) DATE OFF INSTALLATTION ___ __________ _________ ▲Retain this Wa arranty Certificate (upper porrtion) in a safee and convenieent location fo r your records.. HAYWARD H D® Pool Prroducts Liimited Wa arranty To o original purchase ers of this equipm ment, Hayward Po ool Products, Inc.