Installation Guide

ManualsBrandsHayward ManualsOutdoorsPower-Flo LX 1 HP Pool Pump

ISPF SERIES

Rev. C

_____________________________________________________________________________________

OWNER’S MANUAL

INSTALLATION, OPERATION, & PARTS

Power-Flo LX™ / Power-Flo II™ Pump Series

The Hayward

Power-Flo LX™ and Power-Flo II™ Pump Series are specifically engineered for the demanding requirements

of today’s above-ground swimming pools. The advanced design reduces maintenance requirements while providing superior

performance.

To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.

CAUTION – We highly recommend a qualified professional install and service this product.

WARNING – This manual contains important safety information that must be furnished to the end

user of this product. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT

IN SERIOUS INJURY.

*Only units equipped with 3' twist-lock cords

or furnished without a cord for permanent

wiring are UL-Listed.

SAVE THIS INSTRUCTION MANUAL

HAYWARD POOL PRODUCTS, INC.

Corporate Headquarters: U.S.A:

620 Division Street 1 Hayward Industrial Drive 2935 Sidco Drive 2875 Pomona Blvd.

Elizabeth, NJ 07207 Clemmons, NC 27012 Nashville, TN 37204 Pomona, CA 91768

Canada: Europe:

2880 Plymouth Drive Parc Industriel de la plaine de l'ain

Oakville, Ontario L6H 5R4 Allêe des chênes

01150 St Vulbas

France

Summary of content (12 pages)

PAGE 1
ISPF SERIES Rev. C _____________________________________________________________________________________ OWNER’S MANUAL INSTALLATION, OPERATION, & PARTS Power-Flo LX™ / Power-Flo II™ Pump Series The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series are specifically engineered for the demanding requirements of today’s above-ground swimming pools. The advanced design reduces maintenance requirements while providing superior performance.
PAGE 2
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ PRODUCT REGISTRATION (Retain For Your Records) DATE OF INSTALLATION ____________________ INITIAL PRESSURE GAUGE READING (CLEAN FILTER) _______________________ PUMP MODEL ________________ HORSEPOWER _______________________ FILTER MODEL ________________ SERIAL NUMBER _______________________ IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be f
PAGE 3
Power-Flo LX™ / Power-Flo II™ Pump Series __________ ____________ NOTE: The National Electrical Code (NEC) permits use of a cord with a maximum 3 ft. (1 m) length. If your pump is equipped with a cord complying with the NEC, the following three (3) items apply. WARNING – Risk of Electric Shock. Connect only to a grounding type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI.
PAGE 4
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ Installation Instructions Pump Location The Power-Flo LX™ pump MUST be installed below the pool water line (see Figure to right). Self-priming Power-Flo II™ pumps may be installed up to four (4) feet above the pool water line. Install pump on a firm, level base or pad to meet all local and national codes. The field supplied base or pad must be level and vibration-free.
PAGE 5
Power-Flo LX™ / Power-Flo II™ Pump Series_____________________________________________ Installation Instructions (cont.) Fittings Fittings restrict flow. For better efficiency, use the fewest possible fittings. Avoid fittings that could cause an air trap. Pool and spa fittings MUST conform to the International Association of Plumbing and Mechanical Officials (IAPMO) standards. Use a non-entrapping suction fitting in pool or double suction (skimmer and main drain).
PAGE 6
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ Installation Instructions (cont.) Electrical (cont.) Wiring (cont.) In case of a power outage, check GFCI for tripping, which will prevent normal pump operation. Reset if necessary. NOTE: If you do not use conduit when wiring motor, be sure to seal wire opening on end of motor to prevent dirt, bugs, etc., from entering.
PAGE 7
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ Storage/Winterization WARNING – Explosion Hazard. Purging the system with compressed air can cause components to explode, with risk of severe injury or death to anyone nearby. Use only a low pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping. CAUTION – Allowing the pump to freeze will void the warranty.
PAGE 8
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ Shaft Seal Change Instructions (cont.) Exercise extreme care in handling both the rotating and the stationary sections of the two-part replacement seal. Foreign matter or improper handling will easily scratch the graphite and ceramic sealing surfaces. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
PAGE 9
Power-Flo LX™ / Power-Flo II™ Pump Series ___________________________________________ Troubleshooting (cont.) Motor Hums, But Does NOT Start – Check For: 1. 2. Centrifugal switch stuck in OPEN position. Binding of motor shaft. Pump Won’t Prime 1. 2. 3. Make sure pump/strainer housing is filled with water and the cover O-ring is clean, also be sure it is properly seated in the cover O-ring groove. Make sure strainer cover is locked firmly in position and lubricated with “Jack’s 327.
PAGE 10
Power-Flo LX™ / Power-Flo II™ Pump Series___________________________________________ Replacement Parts Parts Diagram Parts Listing Model No. SP1580, SP1580X15 SW1585X20, SW1585X25 Model No. SP1750, 1775, 1780 SPX1500N2 (8 Req'd.) SPX1580BP SPX1580Z1 SPX1500H SPX1500KA SPX1500N2 (6 Req'd.) SPX1705B SPX1580Z1 SPX1500H SPX1500KA Refer to Part No. on Original Equipment 7 Pump Housing SPX1500AA SPX1580AAP 8 Housing Nut, No. 10-24 Hex Head SPX1500Y2 (7 Req'd.) SPX1500Y2 (8 Req'd.
PAGE 11
Power-Flo LX™ / Power-Flo II™ Pump Series_____________________________________________ HAYWARD® LIMITED WARRANTY This pump was inspected before shipment from our plant. To original purchasers of this pump, Hayward Pool Products, Inc., 620 Division Street, Elizabeth, New Jersey, warrants its products free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase.
PAGE 12