Installation Guide

ManualsBrandsHayward ManualsOutdoorsSuper II 3 HP 3 Phase Pool Pump

WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

P/N: IS3000XAZ-05

Rev. C

__________________________________________________________________________________________

OWNER’S MANUAL

INSTALLATION, OPERATION, & PARTS

*50HZ Models are not UL or CSA Listed.

Super II

™

Pump Series

The Hayward Super II Pump is specifically engineered for the demanding requirements of today’s in-ground swimming pool/spa that

is equipped with large capacity filters, heaters, and pool cleaning equipment. The Super II is a self-priming pump that incorporates an

improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service. The advanced design

provides superior performance while reducing maintenance requirements.

To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.

WARNING – This product should be installed and serviced only by a qualified professional.

CAUTION – A licensed electrician MUST complete, in full, all electrical installations noted in this manual.

SAVE THIS INSTRUCTION MANUAL

Use of non-Hayward replacement parts voids warranty.

ATTENTION

INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE

INSTALLATION,

OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER

OF THIS PRODUCT. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS

INJURY.

HAYWARD POOL PRODUCTS, INC.

620 DIVISION STREET ELIZABETH, NJ 07207 (908) 351-5400

WWW.HAYWARDPOOL.COM

Summary of content (14 pages)

PAGE 1
P/N: IS3000XAZ-05 Rev. C __________________________________________________________________________________________ OWNER’S MANUAL INSTALLATION, OPERATION, & PARTS *50HZ Models are not UL or CSA Listed. Super II™ Pump Series The Hayward Super II Pump is specifically engineered for the demanding requirements of today’s in-ground swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment.
PAGE 2
Super II™ Pump Series ____________________ ___________________________ Page 2 of 14 WARNING – Read and follow all instructions in this owner’s manual and on the equipment. Failure to follow instructions can cause severe injury and/or death. IMPORTANT SAFETY INSTRUCTIONS Before installing or servicing this electrical equipment, turn power supply OFF. Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury.
PAGE 3
Super II™ Pump Series __________ _____ __________________________Page 3 of 14 WARNING – Risk of Electric Shock. Hazardous voltage. Can shock, burn, or cause death. To reduce the risk of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a properly located outlet. It is required that licensed electricians do all electrical wiring. All electrical wiring MUST be in conformance with applicable local and national codes and regulations.
PAGE 4
Super II™ Pump Series __________ _____ ________________________ Page 4 of 14 WARNING – Hazardous Pressure. Pool and spa water circulation systems operate under hazardous pressure during start-up, normal operation, and after pump shut-off. Stand clear of circulation system equipment during pump start-up.
PAGE 5
Super II™ Pump Series__________ _____ ______________________________Page 5 of 14 Product Specifications Installation Instructions WARNING – This product should be installed and serviced only by a qualified professional. Pump Location Locate pump as close to pool as practical and run suction lines as direct as possible to reduce friction loss. Suction lines should have continuous slope upward from lowest point in line. Joints must be tight (but not over-tightened).
PAGE 6
Super II™ Pump Series __________ _____ ______________________ Page 6 of 14 Pump Mounting (cont’d) WARNING – Hazardous Pressure. Pumps, filters, and other equipment/ components of a swimming pool filtration system operate under pressure. Incorrectly installed and/or improperly tested filtration equipment and/or components may fail resulting in injury and/or property damage. Plumbing Use Teflon tape to seal threaded connections on molded plastic components.
PAGE 7
Super II™ Pump Series __________ _____ ________________________ Page 7 of 14 Electrical (cont’d.) Voltage Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor may overheat, causing overload tripping and reduced component life. If voltage is less than 90% or more than 110% of rated voltage when motor is running at full load, consult Power Company.
PAGE 8
Super II™ Pump Series ___________________ ____________________________ Page 8 of 14 Prior to Start-Up (cont’d.) ATTENTION – Do NOT add chemicals to pool/spa system directly in front of pump suction. Adding undiluted chemicals may damage pump and voids warranty. ATTENTION – Before removing strainer cover: 1. 2. 3. STOP PUMP before proceeding. CLOSE VALVES in suction and outlet pipes. RELEASE ALL PRESSURE from pump and piping system using filter manual air relief valve.
PAGE 9
Super II™ Pump Series ___________________ _____________________________ Page 9 of 14 Storage/Winterization WARNING – Separation Hazard. Do not purge the system with compressed air. Purging the system with compressed air can cause components to explode, with risk of severe injury or death to anyone nearby. Use only a low pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping. ATTENTION – Allowing the pump to freeze will void the warranty.
PAGE 10
Super II™ Pump Series ___________________ ______________________________Page 10 of 14 Removing the Impeller (See Parts Diagram on page 11 of this manual for pump component locations.) 3. Remove the motor end cover by removing the two (2) screws or pry off the cap covering the motor shaft. Hex shaped caps must be twisted off. 4.
PAGE 11
Super II™ Pump Series ___________________ ____________________________ Page 11 of 14 Replacement Parts Parts Diagram Parts Listing WWW.HAYWARDPOOL.
PAGE 12
Super II™ Pump Series ___________________ Page 12 of 14 Troubleshooting Motor Will NOT Start – Check For: Make sure the terminal board connections agree with the wiring diagram on motor data plate label. Be sure motor is wired for available field supply voltage (see pump operating label). 1. Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown fuses. Solution: Check all connections, circuit breakers, and fuses.
PAGE 13
Super II™ Pump Series ___________________ ____________________________ Page 13 of 14 Low Flow – Generally, Check For: (cont’d.) 2. Undersized pool piping. Solution: Correct piping size. 3. Plugged or restricted discharge line of filter, valve partially closed (high gauge reading). Solution: Sand filters – backwash as per manufacturer’s instructions; D.E. filters – backwash as per manufacturer’s instructions; Cartridge filters – clean or replace cartridge. 4.
PAGE 14
Super II™ Pump Series ___ Page 14 of 14 HAYWARD® LIMITED WARRANTY This pump was inspected before shipment from our plant. To original purchasers of this pump, Hayward Pool Products, Inc., 620 Division Street, Elizabeth, New Jersey, warrants its products free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase.