Instructions for Use
We would like to congratulate you on purchasing our modern semi-automatic rifle. With it, you now own a superb hunting rifle. You will quickly become familiar with your semi-automatic hunting rifle if you handle it in accordance with these instructions . Special features and advantages: - Modern, well balanced semiautomatic rifle. - Superb accuracy. - Low recoil, thanks to the delayed roller locked bolt system.
Table of Contents Design feature Assemblies Loading the rifle Operating the safety Unloading the rifle Field stripping Stripping the bolt assembly Gap between bolt head and bolt carrier Assembling the rifle Sights Telescopic sight clamp mount Mounting the telescopic sight Parts list of the HK 630, HK 770, HK 940 Semi-automatic hunting rifles Guarantee Page 2 4 5 6 6 7 8, 9 9 10 10 11 12 13,14,15 15 3
Assemblies 1 Upper receiver 2 Bolt, recoil spring and buffer 3 Receiver with barrel, and stock 4 Magazine 4
Loading the rifle Press magazine catch, and the magazine will slide out. Insert filled magazine into the rifle until the magazine catch engages. Then retract the bolt all the way by means of the cocking lever on the right side of the rifle. The catch lever located behind the cocking lever will engage and hold the bolt open. Depressing the catch lever slightly will cause the bolt to snap forward, chamber a round from the magazine, and lock into the receiver. The rifle is now cocked and ready to fire.
Operating the safety All semi-automatic hunting rifles shown in this booklet, provide optimum security, thanks to the striker safety. The safety can only be engaged when the rifle is cocked. To put the rifle on safe, the safety lever must fully cover the red dot. The safety is off when the safety lever fully covers the white dot. Unloading the rifle Remove the magazine by pressing the magazine catch.
Field stripping Under normal conditions, it is only necessary to clean the external components of the rifle and to clean the bore. In the event of heavy fouling or to remove moisture or water in the rifle, it is advisable to strip the rifle for thorough cleaning. Unscrew the hexagon socket screw at the end of the upper receiver all the way. Remove the upper receiver to the rear. Remove buffer and recoil spring.
Stripping the bolt assembly Rotate the bolt head clockwise one quarterturn, and then remove it from the locking piece. Finally, remove locking piece, firing pin and firing pin spring from the bolt head carrier by rotating the locking piece further To assemble the bolt, proceed in the reverse sequence. First slide the firing pin spring onto the firing pin and insert both into the bolt assembly. Then press the locking piece against the firing pin spring and rotate counterclockwise one quarter turn.
Stripping the bolt assembly Attention! When reassembling the semi-automatic hunting rifle, do not forget to insert the locking rollers into the bolt head as otherwise the shooter's safety could not be guaranteed and the bolt system of the rifle would be completely damaged Gap between bolt head and bolt carrier With the bolt in its closed position -the magazine being detachedthe bottom side of the bolt is visible through the magazine well.
Assembling the rifle Insert the bolt assembly into the receiver; when doing this, press in the firing pin and the rollers, and slide all the way to the front. Then insert the buffer and recoil spring into the receiver. Rotate the hexagon socket screw one full turn into receiver. Next, slide the upper receiver onto the receiver body from the rear until the collar of the screw is seated against the recess in the upper receiver. Tighten screw firmly.
Telescopic sight clamp mount Our HK05 clamp mount readily accepts all standard telescopic sights. Should you wish to use an aluminum rail-type telescopic sight, loosen the two hexagon socket screws on the bottom of the 05 clamp mount, slide on the telescopic sight and tighten the two hexagon socket screws firmly at the rails. If you are using a steel telescopic sight, please also use the retaining rings. Mounting the telescopic sight - First press the tension lever on the HK05 clamp mount downward.
Operating principle: Action: Feed: Calibre: Muzzle velocity Weight: Overall length: Length of barrel: Magazine, domestic: Magazine, export: 4 and 10 rounds 2 rounds 4 and 10 rounds 2 rounds 3,6 kg (7.92 Ibs) 1130 mm (44.4 in) 500 mm (19.7 in) 3,2 kg (7.04 Ibs) 1070 mm (42.1 in) 450 mm (17.7 in) HK 770 Recoil operated Delayed roller locked Magazine .308 Win. Recoil operated Delayed roller locked Magazine .223 Remington HK 630 Specifications HK 940 4 and 10 rounds 2 rounds 3,9 kg (8.