Owner manual

ManualsBrandsHES ManualsAccessories for electrical5200

5200 Series Electric Strike

Installation Instructions

HES, Inc.

22630 N. 17th Ave.

Phoenix, AZ 85027

800-626-7590

www.hesinnovations.com

Product Components

Diagram 1: Electrical Specifications

ELECTRICAL RATINGS FOR SOLENOID

MINIMUM WIRE GAUGE REQUIREMENTS SOLENOID VOLTAGE

CONTINUOUS DUTY

12VDC

.24

24VDC

200 50 200

.12 .24-.32 .12

12-16VAC 24VAC

INTERMITTENT DUTY*

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

*10% max duty cycle (2 min. max on time)

Indoor use only

200 feet or less

200 - 300 feet

300 - 400 feet

18 gauge

16 gauge

14 gauge

20 gauge

18 gauge

16 gauge

ASSA ABLOY, the global leader

in door opening solutions

12 & 24 Volt Pigtails

5200 Electric Strike Body

Trim Enhancer (with screws)

Summary of content (6 pages)

PAGE 1
Installation Instructions 5200 Series Electric Strike HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com Product Components 1 2 5200 Electric Strike Body Trim Enhancer (with screws) 3 1 12 & 24 Volt Pigtails 2 3 Diagram 1: Electrical Specifications ELECTRICAL RATINGS FOR SOLENOID Resistance in Ohms Amps CONTINUOUS DUTY 12VDC 24VDC 12-16VAC 24VAC 50 200 50 200 .24 .12 .24-.32 .12 Solenoids are rated at +/- 10% indicated value.
PAGE 2
Installation Directions 2 CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter. Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty. Prepare Frame Prepare Strike 1. Select the appropriate Plug In Connector that matches system power and electrically connect as illustrated in Diagram 2.
PAGE 3
Installation Diagrams 3 DIAGRAM 7: JAMB CUTOUT DIMENSIONS DIAGRAM 6: JAMB VIEW DIAGRAM 5: FAIL SAFE CONVERSION DIAGRAM 6: HORIZONTAL ADJUSTMENT K-NUT a b b Fail Safe a Convert Mode a. Loosen the two #2-56 screws located on the back of the strike as shown above, but do not remove them. b. Move screws to the fail safe position as shown above. c. Tighten screws. Verify a. Slowly turn the horizontal adjustment screws to adjust the strike in-frame.
PAGE 4
Cutout Templates 4 5200 with 501A Faceplate 4-7/8” x 1-1/4” Radius Corner Faceplate Aluminum Jamb Installations 1 -1/4" [31.8] 4 -7/8" [124] 3 -3/8" [85.7] 1 -1/4" [31.8] R 1/8" [3] 4 -7/8" [124] 4 -1/8" [104.8] 1 -7/16" [36.6] 13/16" [20.6] 3/32" [2.3] Inches [mm] 5200 with 502 Faceplate 7-15/16” x 1-7/16” Radius Corner Faceplate Aluminum Frame Installations 1 -7/16" [36.5] 3-3/8" [85.7] R 3/16" [4.1] 7-15/16" [201.6] 7 -15/16" 7 -7/16" [201.6] [189] 13/16" [20.6] 3/32" [2.
PAGE 5
Cutout Templates 5 5200 with 503 Faceplate 6 -7/8” x 1-1/4” Radius Corner Faceplate Aluminum Frame Installations 1 -1/4" [36.5] 3 -3/8" [85.7] R 3/16" [4.1] 6 -7/8" [174.3] 1 -1/4" [31.8] 6 -7/8" 6 -1/8" [174.3] [155.6] 1 -7/16" [36.6] 13/16" [20.6] 3/32" [2.3] Inches [mm] 5200 with 504 Faceplate 10” x 1-3/8” Radius Corner & Flat Faceplate Wood Frame Installations R 1/8" [4] 1 -3/8" [34.9] 1 -3/8" [34.9] 10" [254] 1 -3/8" [34.9] 3 -3/8" [85.7] 13/16" [20.6] 3/32" [2.