Operating Instruction DSH 700X-900X
Table Of Contents
- Original operating instructions
- 1 Information about the documentation
- 2 Safety
- 3 Description
- 4 Technical data
- 5 Preparations at the workplace
- 5.1 Fuel
- 5.2 Assembly and adjustment
- 5.3 Locking rotary movement of the guide wheels
- 5.4 Mounting the gasoline-powered saw on the saw trolley (accessory)
- 5.5 Fitting the water pump (accessory)
- 5.6 Removing the water pump (accessory)
- 5.7 Starting the engine
- 5.8 Checks after starting the engine
- 5.9 Switching the engine off
- 6 Types of work
- 7 Care and maintenance
- 7.1 Maintenance table
- 7.2 Cleaning or replacing the air filter
- 7.3 Replacing a broken starter cord
- 7.4 Replacing the fuel filter
- 7.5 Cleaning the spark plug, setting the spark plug gap or replacing the spark plug
- 7.6 Adjusting the carburetor
- 7.7 Care and maintenance of the machine
- 7.8 Maintenance
- 7.9 Checks after care and maintenance work
- 8 Transport and storage
- 9 Troubleshooting
- 10 Disposal
- 11 Manufacturer’s warranty
- Mode d'emploi original
- 1 Indications relatives à la documentation
- 2 Sécurité
- 3 Description
- 4 Caractéristiques techniques
- 5 Préparatifs
- 5.1 Carburant
- 5.2 Travaux de montage et de réglage
- 5.3 Blocage du mouvement de rotation des roulettes de guidage
- 5.4 Montage de la tronçonneuse à essence sur le chariot de guidage (accessoire)
- 5.5 Montage de la pompe à eau (accessoire)
- 5.6 Démontage de la pompe à eau (accessoire)
- 5.7 Démarrage du moteur
- 5.8 Contrôles après démarrage du moteur
- 5.9 Arrêt du moteur
- 6 Travail
- 7 Nettoyage et entretien
- 7.1 Tableau d'entretien
- 7.2 Nettoyage ou remplacement du filtre à air
- 7.3 Remplacement du câble de démarrage sectionné
- 7.4 Remplacement du filtre carburant
- 7.5 Nettoyage de la bougie d'allumage, réglage de l'écartement des électrodes ou remplacement de la bougie d'allumage
- 7.6 Réglage du carburateur
- 7.7 Entretien de l'appareil
- 7.8 Entretien
- 7.9 Contrôle après des travaux de nettoyage et d'entretien
- 8 Transport et entreposage
- 9 Aide au dépannage
- 10 Recyclage
- 11 Garantie constructeur
- Manual de instrucciones original
- 1 Información sobre la documentación
- 2 Seguridad
- 3 Descripción
- 4 Datos técnicos
- 5 Preparación del trabajo
- 5.1 Combustible
- 5.2 Tareas de montaje y ajuste
- 5.3 Bloqueo del movimiento giratorio de los rodillos de guía
- 5.4 Instalación de la amoladora tronzadora de gasolina en el carro de guía (accesorio)
- 5.5 Montaje de la bomba de agua (accesorio)
- 5.6 Desmontaje de la bomba de agua (accesorio)
- 5.7 Arranque del motor
- 5.8 Comprobaciones después del arranque del motor
- 5.9 Desconexión del motor
- 6 Procedimiento de trabajo
- 7 Cuidado y mantenimiento
- 7.1 Tabla de mantenimiento
- 7.2 Limpieza o sustitución del filtro de aire
- 7.3 Sustitución del cable roto del arrancador
- 7.4 Sustitución del filtro de combustible
- 7.5 Limpieza de la bujía, ajuste de la distancia de los electrodos o sustitución de la bujía
- 7.6 Ajuste del carburador
- 7.7 Mantenimiento de la herramienta
- 7.8 Mantenimiento
- 7.9 Comprobación después de las tareas de cuidado y mantenimiento
- 8 Transporte y almacenamiento
- 9 Ayuda sobre averías
- 10 Reciclaje
- 11 Garantía del fabricante
- Manual de instruções original
- 1 Indicações sobre a documentação
- 2 Segurança
- 3 Descrição
- 4 Características técnicas
- 5 Preparação do local de trabalho
- 5.1 Combustível
- 5.2 Trabalhos de montagem e de afinação
- 5.3 Bloquear o movimento de rotação dos rolos de guia
- 5.4 Montar a ferramenta de corte a gasolina no carro-guia (acessório)
- 5.5 Montar a bomba da água (acessório)
- 5.6 Desmontar a bomba da água (acessório)
- 5.7 Ligar o motor
- 5.8 Verificações após arranque do motor
- 5.9 Desligar o motor
- 6 Trabalhar
- 7 Conservação e manutenção
- 7.1 Tabela de manutenção
- 7.2 Limpar ou substituir o filtro do ar
- 7.3 Substituir um cabo arrancador partido
- 7.4 Substituir o filtro de combustível
- 7.5 Limpar a vela de ignição, ajustar a folga dos eléctrodos ou substituir a vela de ignição
- 7.6 Afinar o carburador
- 7.7 Manutenção da ferramenta
- 7.8 Manutenção
- 7.9 Verificação após trabalhos de conservação e manutenção
- 8 Transporte e armazenamento
- 9 Ajuda em caso de avarias
- 10 Reciclagem
- 11 Garantia do fabricante
*2271385*
2271385 English 11
▶ Hold the guard by the grip provided and rotate it to the desired position.
Make sure that the opening of the blade guard is not toward the user.
5.2.3 Conversion from normal cutting to flush cutting
The front section of the saw arm can be converted to allow flush cuts to be made (e.g. as close as
possible to edges and walls).
▶ If you wish to use the product in the flush cutting position, have the product converted by Hilti Service.
5.3 Locking rotary movement of the guide wheels 4
WARNING
Risk of injury. The saw could move inadvertently or fall down.
▶ When working on roofs, scaffolds and/or slopes, always block the guide rollers to prevent unwanted
movement.
1. Release the guide wheel mounting screws and remove the guide wheels.
2. Reverse the guide wheels (turn through 180°) and refit the mounting screws.
▶ The integrated locking function is active.
3. Check that the guide wheels are securely fastened.
5.4 Mounting the gasoline-powered saw on the saw trolley (accessory) 5
1. Remove the water tank from the saw trolley.
2. Move the cutting depth adjustment lever into the upper position.
3. Open the hold-down device by releasing the screw knob.
4. Fit the saw into the forward mount with the wheels as shown and swing the grip of the saw under the
hold-down device.
5. Secure the saw by tightening the screw knob.
6. Fit the water tank after filling it.
7. Adjust the grip to a convenient working height.
8. Adjust the guard to the correct position. → page 10
Especially when using the machine in this configuration for the first time, check to ensure that the
throttle cable is correctly adjusted. When the throttle trigger is pressed fully, the product must run
up to maximum speed. If this is not the case, the throttle cable can be readjusted by way of the
cable tensioner.
When the throttle is not actuated, the engine must be idling and the cutting disc must not rotate.
If this is not the case, switch off by pushing the run/stop switch to the “stop” position and then
adjust the throttle cable or have the idling speed adjusted by Hilti Service.
5.5 Fitting the water pump (accessory) 6
1. Switch the product off.
2. Release the three pump cover retaining screws, remove the parts and store the pump cover in a safe
place.
The pump cover must be fitted if the tool is used without the water pump.
3. Hold the water pump in position and turn the cutting disc slightly to bring the splines of water pump and
clutch bell into alignment so that the splines engage.
▶ The position is keyed so it is not possible to position the pump incorrectly.
4. Install the three retaining screws and tighten them to the specified tightening torque (tightening torque:
8 Nm).
5. Connect the pump hose to the hose connector on the saw.
6. Remove the protective cap from the end of the water connection hose.