S-BT Threaded Fastener Specification
Table Of Contents
- 1.1 Definition
- 1.2 The S-BT system
- 1.3 Fastening mechanism
- 1.4 S-BT system features and benefits – simplified fastening to steel
- 2.1 Grating fastening system
- 2.2 Grating fastening system X-FCS-R
- 2.3 S-BT with MM and MQ installation channel system
- 2.4 Fastening instrumentation, junction boxes and lighting
- 2.5 Fastening cable / conduit connectors
- 2.5 Fastening cable tray supports
- 2.7 Electrical connections
- 3.1 Product data
- 3.2 Load data
- 4.1 Instruction for use - S-BT-MF M6, M8, M10, W6, W10
- 4.2 Instruction for use - S-BT-MF M8/7 AN 6
- 4.3 Instruction for use - S-BT-MR M6, M8, M10, W6, W10 SN 6
- 4.4 Instruction for use - S-BT-MR M8/7 SN 6
- 4.5 Instruction for use - S-BT-MR M6, M8, M10, W6, W10 SN 6 AL
- 4.6 Instruction for use - S-BT-MR M8/7 SN 6 AL
- 4.7 Instruction for use - S-BT-GF M8/7 AN 6
- 4.8 Instruction for use - S-BT-GR M8/7 SN 6
- 4.9 Instruction for use - S-BT-GR M8/7 SN 6 AL
- 4.10 Instruction for use – S-BT-EF M6/W6/M8
- 4.11 Instruction for use – S-BT-EF M10/W10
- 4.12 Instruction for use – S-BT-ER M6/W6/M8
- 4.13 Instruction for use – S-BT-ER M10/W10
- 4.14 Instruction for use – S-BT-EF W10 HC AWG2/0 and S-BT-EF M10 HC 35/120
- 4.15 Instruction for use – S-BT-ER W10 HC AWG2/0 and S-BT-ER M10 HC 35/120
- 5.1 Nomenclature and symbols
- 5.2 Design concepts
- 5.3 Static capacity of the S-BT threaded stud
- 5.4 Vibration effects on S-BT threaded stud fastenings
- 5.5 Resistance of S-BT fastenings under dynamic tensile loading
- 5.6 Effect of S-BT threaded stud fastenings on the fatigue strength of base material structural steel
- 5.7 Influence of glue coatings on the loosening torque
- 5.8 S-BT-ER and S-BT-EF screw-in threaded studs for electrical connections
- 5.9.5 Conductivity disc of S-BT-ER / -EF electrical connectors
- 5.9.4 Stainless steel S-BT studs
- 5.9.3 Carbon steel S-BT studs
- 5.9.2 Galvanic (contact) corrosion
page18 Specifications
1
3
2.1
!
!
5
2.0
4
Marklocationofeach
fastening.
Screw-inS-BTstudsinto
drilled hole.
Pre-drillwithTS-BT
stepped drill bit.
Screwontheconnector
and hand tighten.
Pre-drilluntilshoulder
grinds a shiny ring.
The drilled hole and the
areaarounddrilledhole
mustbecleanandfree
fromliquidsanddebris.
Align connectors.
Fastenthecable / conduit
on the connector.
2.6 Fasteningcable / conduitconnectors
Stainless steel and carbon steel S-BT screw-in threaded studs for fastening
cable and conduit connectors (T-bars) to coated steel.
Installation instructions
Hold down clamp
Expansion guide clip
2.7 Fastening cable tray supports
Stainless steel and carbon steel threaded studs for fastening cable trays to
coated steel.
Installation instructions
Important notes:
Theseareabbreviatedinstructionswhichmayvarybyapplication.
Alwaysreview / followtheinstructionsforuse(IFU)accompanyingtheproduct.
In case of a drill through hole,reworkofthecoatingonthebacksideofthe
plate / prolemaybeneeded.