S-BT Threaded Fastener Specification
Table Of Contents
- 1.1 Definition
- 1.2 The S-BT system
- 1.3 Fastening mechanism
- 1.4 S-BT system features and benefits – simplified fastening to steel
- 2.1 Grating fastening system
- 2.2 Grating fastening system X-FCS-R
- 2.3 S-BT with MM and MQ installation channel system
- 2.4 Fastening instrumentation, junction boxes and lighting
- 2.5 Fastening cable / conduit connectors
- 2.5 Fastening cable tray supports
- 2.7 Electrical connections
- 3.1 Product data
- 3.2 Load data
- 4.1 Instruction for use - S-BT-MF M6, M8, M10, W6, W10
- 4.2 Instruction for use - S-BT-MF M8/7 AN 6
- 4.3 Instruction for use - S-BT-MR M6, M8, M10, W6, W10 SN 6
- 4.4 Instruction for use - S-BT-MR M8/7 SN 6
- 4.5 Instruction for use - S-BT-MR M6, M8, M10, W6, W10 SN 6 AL
- 4.6 Instruction for use - S-BT-MR M8/7 SN 6 AL
- 4.7 Instruction for use - S-BT-GF M8/7 AN 6
- 4.8 Instruction for use - S-BT-GR M8/7 SN 6
- 4.9 Instruction for use - S-BT-GR M8/7 SN 6 AL
- 4.10 Instruction for use – S-BT-EF M6/W6/M8
- 4.11 Instruction for use – S-BT-EF M10/W10
- 4.12 Instruction for use – S-BT-ER M6/W6/M8
- 4.13 Instruction for use – S-BT-ER M10/W10
- 4.14 Instruction for use – S-BT-EF W10 HC AWG2/0 and S-BT-EF M10 HC 35/120
- 4.15 Instruction for use – S-BT-ER W10 HC AWG2/0 and S-BT-ER M10 HC 35/120
- 5.1 Nomenclature and symbols
- 5.2 Design concepts
- 5.3 Static capacity of the S-BT threaded stud
- 5.4 Vibration effects on S-BT threaded stud fastenings
- 5.5 Resistance of S-BT fastenings under dynamic tensile loading
- 5.6 Effect of S-BT threaded stud fastenings on the fatigue strength of base material structural steel
- 5.7 Influence of glue coatings on the loosening torque
- 5.8 S-BT-ER and S-BT-EF screw-in threaded studs for electrical connections
- 5.9.5 Conductivity disc of S-BT-ER / -EF electrical connectors
- 5.9.4 Stainless steel S-BT studs
- 5.9.3 Carbon steel S-BT studs
- 5.9.2 Galvanic (contact) corrosion
Specifications page59
S-BT Screw-in threaded studs
4.16Instructionforuse–StandoffadapterMFandMR25/50/75/100onsteel
withapassivereprotection(PFP)coating
4.16.1Instructionforuse–CalibrationofdepthgaugeS-DGBTforinstallation
of S-BT on PFP-coated steel (e.g. S-BT GR M8/7 SN 6)
1×
S-NS 19
Torque tool X-BT 1/4"
8 Nm / 5.9 ft.lb
S-BT–GR M8/7 SN 6
S-BT–GF M8/7 AN 6
TS-BT 31-74 PFP
≤ 0,8 mm / 0.03"
≥ 6 mm / 1/4"
≤ 0,8 mm / 0.03"
S-BT–MR M10/W10/15 SN 6
S-BT–MF M10/W10/15 AN 6
SBT 4-A22
M8 MR/MF 25
M8 MR/MF 50
M8 MR/MF 75
M8 MR/MF 100
M10 MR/MF 50
W10 MR/MF 50
S-DG BT M8/7 SHORT 6
S-DG BT M10-W10/15 LONG 6
S-CC BT 6
SBT 4-A22
GEAR
#2
SBT 4-A22
GEAR
#1
1×
(1-3)
1
1
2
(1-3)
3
(1-3)
S-DG BT M10-W10/15 LONG
S-DG BT M8/7 Short 6
≤100 mm/4"
1
2
3
4
5
6
7
8
9
10
11
2275221-11.2020
2275221
24.11.2020
PFP-Removal Drill Bit S-BT
CALIBRATION