Model 100L5G 120L5G Quick Setup Guide Before using the Laser Cinema, please read this guide carefully and keep it for future reference. Disclaimer: This Quick Setup Guide is intended as a general guideline to help you set up your Laser Cinema. Images throughout this document are for illustrative purposes only and may differ from the actual product.
© 2021 Hisense Company Ltd. All Rights Reserved. All material in this Quick Setup Guide is the property of Hisense Company Ltd. and its subsidiaries, and is protected under US, CANADA, MEXICO and International copyright and/or other intellectual property laws. Reproduction or transmission of the materials, in whole or in part, in any manner, electronic, print, or otherwise, without the prior written consent of Hisense Company Ltd. is a violation of Hisense Company Ltd. rights under the aforementioned laws.
Congratulations on the purchase of your new Laser Cinema! This Quick Setup Guide will walk you through a few easy steps to set up your Laser Cinema. Table of Contents Register Your Laser Cinema! 2 Important Safety Information 3 Packaged Contents 5 Laser Cinema Diagram 6 STEP 1. Mount the Screen 7 STEP 2. Set up the Laser Cinema 7 STEP 3. Adjust the Display Image and the Screen 10 STEP 4.
Register Your Laser Cinema! Because we value your business, we want to keep you in the know of 'all things Hisense'. Using your mobile phone, scan the Registration page QR code to register your Laser Cinema. Depending on the make and model of your phone, you may need to download a QR code scanning app. U.S. http://www.hisense-usa.com/support/ register Mexico https://hisense.com.mx/support/register 2 Canada http://www.hisense- canada.com/ support/productReg.
Important Safety Information SAFETY WARNINGS Do not look directly at the lens when this device is on! • This product comes with a laser module. Do not tear or modify this device in any manner; otherwise, it may result in personal injury.
• If this device has been in a warm environment, allow any built-up condensation to evaporate first BEFORE you switch the device on. • Do not allow a child to stand on or climb up this device. • Do NOT place any object above or in front of the lens because the laser light could cause the object to become flammable. • Clean the lens periodically with a clean cloth and make sure the Laser Cinema is turned off before you start.
Packaged Contents • • • • • • • Laser Cinema 1 Remote control 2 AAA batteries 2 pairs of gloves for handling the Laser Cinema 1 Power Cord 1 Wrench to adjust the bottom of the Laser Cinema 1 Audio Out Cable • • • • • • Hisense 4K Laser Cinema Quick Setup Guide Important Safety Information & Warranty Card Cleaning kit for the lens 2 C-shaped blocks C-shaped Block Installing Instruction 1 USB extension cable ADDITIONAL ITEMS THAT COME WITH THE LASER CINEMA IN A SEPARATE PACKAGE • A Display Screen (optiona
Laser Cinema Diagram Power Indicator Air vents Remote control receiver Eye protection sensor Lens with laser Power button We strongly recommend that two people handle this device when moving it from one place to another. Be sure to protect the lens when you handle this device.
STEP 1 Mount the Screen If you purchased a screen from Hisense to include with your Laser Cinema, then refer to the Screen Installation Guide that’s included in the package. STEP 2 Set up the Laser Cinema To begin setting up the Laser Cinema, we strongly recommend that TWO people move it from one place to another because of the weight. Be sure to protect the lens when you handle this device. 1.
Ports to connect certain cables to USB devices for browsing photos, music and movies. This unit only recognizes USB Memory Sticks. NOTE: Use the USB extension cable (included) for easier connection and disconnection. When connecting a hard disk or a USB hub, always connect the mains adapter of the connected device to the power supply. Exceeding a total current consumption may result in damage. The USB2.0 device maximum current consumption is 500mA. The USB3.0 device maximum current consumption is 1A.
External AV devices HDMI VCR DVD Player Set-top Box White 4 audio adapter Red Video Camera Satellite Receiver External audio devices Digital audio adapter Speakers It may be used to connect to a home automation system or Custom Integrated Audio/Video (A/V) system. It is recommended that it should only be completed by a professional installer.
STEP 3 Adjust the Display Image and the Screen Follow the steps in the order shown below, only if they apply to your situation. Note: Before adjusting, fold the wall-mount bracket wands so that screen is vertically level. Rotate feet from an overlooking view, but do not look directly at the lens when this device is on because the laser light may damage your eyes.
ADJUST THE UPPER-RIGHT CORNER OF THE IMAGE 1. If the top of the image is lower on the left and higher on the right, then use the wrench to rotate the front-right foot and the back-right foot clockwise to the same height. • If the bottom of the image is wider than the screen, then move the Laser Cinema closer to the screen. back-right foot If the bottom of the image is narrower than the screen, then move the Laser Cinema farther from the screen. front-right foot 2.
4. If the upper-right corner is inside the screen after adjusting, use the wrench to rotate the front-right foot and the backright foot counterclockwise to the same height, and rotate the Laser Cinema clockwise, to make the image parallel with the screen. 2. Now, rotate the Laser Cinema clockwise so that the bottom of the image is parallel with the screen. ADJUST THE UPPER-LEFT CORNER OF THE IMAGE 1.
FILL THE TOP OF THE IMAGE TO THE SCREEN If the top of the imge is wider than the screen, then use the wrench to rotate the left- and right-front feet of the Laser Cinema clockwise. If the top of the image is narrower than the screen, then use the wrench to rotate the left- and right-back feet of the Laser Cinema clockwise, until the left and right borders of the image are parallel with the screen borders. Next, move the projector further from the screen to fill the image to screen width.
STEP 4 Use Your Remote BUTTON BUTTON DESCRIPTION Power on/off INPUT FAV OK Display the Home screen Change Laser Cinema input source Enter Channels/input numbers and special function buttons Press to enter your customized input source/app Press and hold to enter customization settings VOL CH Volume (up/down) Channel (up/down) Google Assistant of Laser Cinema Confirmation button / ˄/˅/˂/˃ DESCRIPTION D-pad (up/down/left/right navigation buttons) Press to enter Menu Press and hold to pair the blue
1. Press and slide the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the (+) and (-) ends of the batteries with the (+) and (-) ends indicated in the battery compartment. 3. Restore the battery compartment. • It can work at a 30 degree horizontal or 15 degree vertical angle.( This angle is used by infrared means in an unpaired state.) PAIRING THE REMOTE CONTROL 1. Pair the remote to the Laser Cinema after you power it on.
STEP 5 Proceed through the Screen Setup Menu 4. Click "+" on your mobile device to take a photo of the entire screen and image. For best results, stand about 10 feet away from the screen and use landscape mode. 5. Click "upload" on your mobile device to complete the automatic geometric correction. PROJECTION MODE If you need to flip the image over top-to-bottom and/or leftto-right, select the Projection Mode and press the UP/DOWN buttons.
Begin to Enjoy Your Laser Cinema Text-to-Speech(TTS) and Video Description functionalities on Laser Cinema Your Smart Laser Cinema is easy to use and bragworthy! Text-to-Speech (TTS) and Video Description can help you to navigate the menus on the screen and hear an audio description of relevant programs. Text-to-Speech can convert written text into voice text to help visually impaired people listen to the information they are unable to read.
Maintenance • Do not touch this device when it is running or just turned off because it may be hot. • Do not wipe this device with oil because it may deteriorate the exterior or damage the paint. Contact with rubber or ethylene products for a long time may cause stains on this device. • If the outside of the Laser Cinema is dirty, turn off the Laser Cinema and wipe with a damped soft cloth. • Do not touch the lens with your hands. • Do not touch or wipe the lens with ordinary cleaning cloth.
3. Check to see if the LED light is on or not. If it is, then the Laser Cinema is receiving power. I have connected an external source to my Laser Cinema and I get no picture and/or sound. 1. Check for the correct output connection on the external source and for the correct input connection on the Laser Cinema. 2. Make sure you have made the correct selection for the input mode for the incoming signal. The picture is normal but there is no sound 1. Check the volume settings. 2.
The remote control does not work 1. Confirm that Laser Cinema still has power and is operational. 2. Change the batteries in the remote control. 3. Check if the batteries are correctly installed. NEED MORE HELP? Additional help is available online at support links. You will find answers to frequently asked questions, downloadable firmware and more. If the problem is still not resolved, then contact us at one of the phone numbers below. U.S.A. http://www.hisense-usa.com/support/ MEXICO http://www.hisense.
Product Specifications MODEL NAME 100L5G DIMENSION (W × H × D) 21.5 × 6.2 × 13.6 inches (547 × 158 × 346 mm) WEIGHT 24.3 lbs (11.
RECEIVING CHANNELS VHF: 2 - 13, UHF: 14 - 69, CATV: 1 - 125 Digital Terrestrial Broadcast (8VSB): 2 - 69 Digital cable (64/256 QAM): 1 - 135 TUNER TYPE Frequency synthesized RECEIVING SYSTEM Analog: NTSC Digital: ATSC/QAM Disclaimer: All products, product specifications, and data are subject to change without notice to improve reliability, function, design or otherwise.
Certification and Compliance The Wi-Fi Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated FCC Notice with a minimum distance of 20 centimeters between the radiator and your body. Declaration of Conformity This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
ES-L212114-1
