OM-928 2007−01 Processes Air Plasma Cutting and Gouging Description Air Plasma Cutter AirForce 250A ™ And ICE-12C Torch 198 842J
From Hobart to You Thank you and congratulations on choosing Hobart. Now you can get the job done and get it done right. We know you don’t have time to do it any other way. This Owner’s Manual is designed to help you get the most out of your Hobart products. Please take time to read the Safety precautions. They will help you protect yourself against potential hazards on the worksite. We’ve made installation and operation quick and easy.
TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2. Plasma Arc Cutting Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3.
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING pom _nd_5/04 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message. . Means “Note”; not safety related. This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the hazards. 1-2.
EXPLODING PARTS can injure. D On inverter power sources, failed parts can explode or cause other parts to explode when power is applied. Always wear a face shield and long sleeves when servicing inverters. D D D D FLYING SPARKS can cause injury. Sparks and hot metal blow out from the cutting arc. Chipping and grinding cause flying metal. D D D Wear approved face shield or safety goggles with side shields. Wear proper body protection to protect skin.
1-3. Additional Symbols For Installation, Operation, And Maintenance HOT PARTS can cause severe burns. D Do not touch hot parts bare handed. D Allow cooling period before working on torch. MOVING PARTS can cause injury. D Keep away from moving parts such as fans. D Keep all doors, panels, covers, and guards closed and securely in place. FLYING METAL can injure eyes. D Wear safety glasses with side shields or face shield. MAGNETIC FIELDS can affect pacemakers. D Pacemaker wearers keep away.
1-5. Principal Safety Standards Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402. Recommended Practices for Plasma Arc Cutting, American Welding Society Standard AWS C5.2, from American Welding Society, 550 N.W.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION pom_fre 5/04 2-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par des symboles adjacents aux directives. Y Identifie un message de sécurité particulier. . Signifie NOTA ; n’est pas relatif à la sécurité.
D Isoler la pince de masse quand pas mis à la pièce pour éviter le contact avec tout objet métallique. Il y a DU COURANT CONTINU IMPORTANT dans les convertisseurs après la suppression de l’alimentation électrique. D Arrêter les convertisseurs, débrancher le courant électrique, et décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie entretien avant de toucher les pièces. Tableau 1.
LES BOUTEILLES peuvent exploser si elles sont endommagées. Les bouteilles de gaz contiennent du gaz sous haute pression. Si une bouteille est endommagée, elle peut exploser. Puisque les bouteilles de gaz font habituellement partie d’un processus de travail des métaux, assurez−vous de les manipuler correctement. D Protégez les bouteilles de gaz comprimé contre la chaleur excessive, les chocs mécaniques, le laitier, la flamme, les étincelles et l’arc.
2-4. Principales normes de sécurité Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Welding Society, 550 N.W. Lejeune Rd, Miami FL 33126 Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402. Recommended Safe Practice for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, norme AWS F4.1, de l’American Welding Society, 550 N.W.
SECTION 3 − DEFINITIONS 3-1.
SECTION 4 − INSTALLATION 4-1. Specifications For Power Source Primary Primary Volts Amperes 120 Primary Service (Recommended) Secondary Volts (DC) Secondary Amperes KW KVA 20A 110 12 2.01 2.44 20.32 (0.25*) Rated Cutting Capacity 0.25 in (6.4 mm) At 6 IPM (2.5 mm/s) Power Factor Max** OCV (DC) 0.82 353 *While idling **10% High line condition 4-2. Specifications For Torch Air-cooled torch for plasma arc cutting (PAC) 35% duty cycle Gas flow/pressure: 1 SCFM (28.
4-4. Torch Dimensions And Weight 8-3/8 in (213 mm) 1 in (25 mm) 1-3/8 in (35 mm) 3.0 lb (1.4 kg) Ref. 801 397-A 4-5. Selecting A Location 6-3/4 in (171 mm) Dimensions And Weight 17 in (432 mm) 42 lb (19.1 kg) 18 in (457 mm) 1 Movement 1 Lifting Handle Use handle to lift unit. 2 2 Hand Cart Use cart or similar device to move unit. 3 120 VAC Receptacle Locate unit near correct input power supply.
4-6. Connecting Work Clamp 1 2 1 Work Clamp Workpiece Connect work clamp to a clean, paint-free location on workpiece, as close to cutting area as possible. 2 802 463-A 4-7. Connecting Input Power Check input voltage available at site. 1 2 1 Grounded Receptacle A 120 volt, 20 ampere individual branch circuit protected by time-delay fuses or circuit breaker is required (see Section 4-1). 2 Plug From Unit Select extension cord of 12 AWG for up to 75 ft (23 m) or 10 AWG for up to 140 ft (46 m).
SECTION 5 − OPERATION 5-1. Controls 1 2 POWER OFF CUP ON TEMP INPUT VOLTAGE 3 196 630 1 2 Power Switch 3 Power Light Trouble Light Trouble light comes on for the following conditions: Use light to tell if unit is energized and ready to operate. Light goes off if input power is not with specified range (see trouble light information).
5-3. Sequence Of Operation . Moisture from the compressor will form in the air line and at EXAMPLE Of Cutting Operation the torch. It will be normal to sometimes see moisture come out the end of the torch. The pilot arc starts immediately when trigger is pressed. For shielded cutting, place drag shield on edge of metal. For non-shielded cutting, use 1/8 in (3.2 mm) standoff distance (dragging tip will reduce tip life). Adjust torch speed so sparks go thru metal and out bottom of cut.
SECTION 6 − MAINTENANCE & TROUBLESHOOTING 6-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more often during severe conditions.
6-2. Trouble Light And Checking Shield Cup Shutdown System If certain problems occur, the trouble light comes on, and output stops. 1 Trouble Light a 1 CUP TEMP INPUT VOLTAGE Turn power Off, and check shield cup connection (see Item 2 below). Power must be reset whenever the cup shutdown is activated. Check shield cup shutdown system once a week. Checking Torch Shield Cup Shutdown System Power source Power switch must be reset whenever cup shutdown system is activated.
6-3. Torch And Work Cable Connections If torch or work cable needs to be removed or replaced, proceed as follows: 5 4 7 8 6 Torch Connections Remove existing torch cable from unit. 1 5 Turn power Off, and disconnect input power plug from receptacle. Remove wrapper from unit. 1 Strain Relief 2 Torch Cable Insert cable through strain relief. Slide strain relief nut onto torch cable, but do not tighten. 6 2 3 Install air line connector onto compressor fitting.
6-4. Checking/Replacing Retaining Cup, Tip, And Electrode Overtightening will strip threads. Do not overtighten retaining cup during assembly. Do not cross-thread parts causing stripping. Use care during torch assembly and parts replacement. Inspect shield cup, tip, and electrode for wear before cutting or whenever cutting speed has been significantly reduced. Do not operate torch without a tip or electrode in place. Be sure to use genuine replacement parts.
6-5. Troubleshooting Power Source Is input power connected to correct line voltage? No Connect unit to proper input voltage. (see Section 4-7). Yes Is Power switch in the On position? No Place Power switch in the On position. (see Section 5-1). Does pilot arc ignite? No Press torch trigger and check if pilot arc ignites. Check torch consumables. *Check torch connections, relay CR1, gas/air system, and torch. Yes No * Check Power switch S1, relay CR2, and thermistor R1.
6-6. Troubleshooting Torch Does arc go on and off while cutting? Yes Torch travel speed too slow; increase travel speed (see Section 4-2). Clean or replace torch consumables as necessary (see Section 6-4). Be sure work clamp is securely attached to workpiece. Go to Section 6-5. Be sure work clamp is securely attached to workpiece. Make sure drag shield contacts metal while cutting. Clean or replace torch consumables as necessary (see Section 6-4). Go to Section 6-5.
SECTION 7 − ELECTRICAL DIAGRAM 230 564-A Figure 7-1.
SECTION 8 − PARTS LIST . Hardware is common and not available unless listed. 2 1 3 4 35 5 6 7 8 34 9 10 33 32 11 12 30 29 31 13 14 15 28 20 16 27 26 25 17 24 23 19 21 18 22 Ref. 802 591-F Figure 8-1.
Item No. Dia. Mkgs. Part No. Description Quantity Figure 8-1. Main Assembly . . . . . . . . . . . . . . . . . . . 212 524 . . . 1 . . . . . . . . . . . . +195 621 . . . 2 . . . . . . . . . . . . . 197 336 . . . 3 . . . . . . . . . . . . . 208 015 . . . 4 . . . . . . . . . . . . . 196 851 . . . . . . . . . . . . . . . . . . . 184 791 . . . 5 . . . . . FM . . . . 195 610 . . . 6 . . . . CR2 . . . 149 823 . . . 7 . . . . . R1 . . . . 182 486 . . . 8 . . . . . . . . . . . . . 200 000 . . . 9 . . . . CR1 .
1 Item Part No. No. 2 3 6 1 183 427 2 3 4 5 6 171 248 196 931 196 930 196 932 185 833 190 220 169 231 196 923 Description Handle Assy, left and right w/screws (1) Pushbutton Switch (1) Leads, 20ft (1) Label, ICE-12C (1) Main Body (1) Switch Assy w/Spring (1) Spring, trigger assy (1) Grease, silicone (1) Torch, replacement (1) 5 4 1 Figure 8-2. Torch, ICE-12C S and CE markings only apply when the torch is used with shielded parts: retaining cup (197 567) and drag shield (196 929).
Notes
Notes
Effective January 1, 2006 5/3/1 WARRANTY applies to all Hobart welding equipment, plasma cutters and spot welders with a serial number preface LG or newer. Warranty Questions? Call 1-800-332-3281 7 AM − 6 PM EST Service You always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281.
Owner’s Record Please complete and retain with your personal records. Model Name Protect Your Investment! Serial/Style Number Purchase Date (Date which equipment was delivered to original customer.) Distributor Address City Register your product at: HobartWelders.com State Zip Resources Available Always provide Model Name and Serial/Style Number. To locate a Distributor, retail or service location: Call 1-877-Hobart1 or visit our website at www.HobartWelders.
