manual
Remark: please debug the motor on the ground after successfully altering the angle of entrance in motor.
Setting for accelerated startup: provide rapid accelerated start up with linear throttle response.
Ultra smooth startup: the lag time of throttle response between t he starting and highest speed is 1.5 seconds.
The setting mode can prevent the precision gear/gearing dropping under momentary load. The setting mode is
recommended to use in fixed wing model with gear box or helicopter.
Smooth startup: the lag time of throttle response between the starting and highest speed is 1 second. The
setting mode is recommended to use in fixed wing model with gear box or helicopter.
Accelerated startup: there is no lag time of throttle response between the starting and highest speed. The
setting mode is recommended to use in fixed wing model with direct drive.
6.
6.
6.
6. The
The
The
The Mode
Mode
Mode
Mode for
for
for
for helicopter:
helicopter:
helicopter:
helicopter: (use
(use
(use
(use in
in
in
in application
application
application
application of
of
of
of helicopter)
helicopter)
helicopter)
helicopter)
Turn off the helicopter
Helicopter 1: the lag time of throttle response between the starting and highest speed is 5 seconds. However,
if the throttle is turned off after startup, the next startup will commence in common mode.
Helicopter 1: the lag time of throttle response between the starting and highest speed is 15 seconds.
However, if the throttle is turned off after startup, the next startup will commence in common mode.
Remark: once working under mode for helicopter, the brake and types of protection under low voltage will
be reset automatically to mode of no brake and reduce power mode separately regardless of previous setting of
ESC.
7.
7.
7.
7. Steering
Steering
Steering
Steering motor
motor
motor
motor (clockwise/anticlockwise)
(clockwise/anticlockwise)
(clockwise/anticlockwise)
(clockwise/anticlockwise)
In most cases, the clockwise and anticlockwise rotation of motor can be realized by exchanging any two
lines among the three output lines in the ESC connected to the motor. The direction of rotation can be changed
by altering the setting value on the ESC in case that the wire connected to motor has been directly welded on
the ESC.
8
8
8
8 .
.
.
. Operating
Operating
Operating
Operating frequency
frequency
frequency
frequency ： 8kHz
8kHz
8kHz
8kHz /
/
/
/ 16kHz
16kHz
16kHz
16kHz
8 kHz-the Operating frequency for motor with 2 poles, for example inner rotor
16 kHz-the Operating frequency for motor with poles more than 2, for example outer rotor
Although the operating frequency of 16 kHz can provide strong power for fixed wing or helicopter, the
default setting is 8 kHz for there are louder RF noise under the operating frequency of 16 kHz.
9.
9.
9.
9. Protection
Protection
Protection
Protection mode
mode
mode
mode under
under
under
under low
low
low
low voltage:
voltage:
voltage:
voltage: reduce
reduce
reduce
reduce power/
power/
power/
power/ halt
halt
halt
halt immediately
immediately
immediately
immediately
Reduce power- the ESC will reduce the output power of motor when reaches default protection threshold
for low voltage (recommend)
Halt immediately-the ESC will cut off the output power of motor when reaches default protection threshold
for low voltage
V.
V.
V.
V.
The
The
The
The order
order
order
order and
and
and
and introduction
introduction
introduction
introduction of
of
of
of circle
circle
circle
circle menu
menu
menu
menu under
under
under
under programming
programming
programming
programming mode
mode
mode
mode
●
Turn on ESC- push the throttle to the highest position-connect the ESC to battery- wait two second-enter
programming mode
After enter programming mode, the following beeps will give out in accordance with the following circuit.
After certain warning tone, push the throttle to the lowest position during the four beeps.
Confirm and reserve the setting.
The
The
The
The introduction
introduction
introduction
introduction for
for
for
for the
the
the
the setting
setting
setting
setting of
of
of
of programming
programming
programming
programming