Instructions / Assembly

ManualsBrandsHome Accents Holiday ManualsArtificial Christmas Trees9 ft Jackson Noble Fir Pre-Lit LED Artificial Christmas Tree with 1500 Color Changing Micro Dot Lights

Safety Information

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical products, basic precautions should always be

followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS.

b) This product is for indoor use only. The electrical rating 0.57 A 120 V 60

Hz.

c) Do not use seasonal products outdoors unless marked suitable for

indoor and outdoor use. When products are used in outdoor applications,

connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If

one is not provided, contact a qualified electrician for proper installation.

d) This seasonal use product is not intended for permanent installation or

use.

e) Do not mount or place near gas or electric heaters, fireplace, candles or

other similar sources of heat.

f) Do not secure the wiring of the product with staples or nails, or place on

sharp hooks or nails.

g) Do not let lamps rest on the supply cord or on any wire.

h) Unplug the product when leaving the house, when retiring for the night,

or if left unattended.

i) This is an electric product – not a toy! To avoid risk of fire, burns personal

injury and electric shock it should not be played with or placed where small

children can reach it.

j) Do not use this product for other than its intended use.

k) Do not hang ornaments or other objects from cord, wire, or light string.

l) Do not close doors or windows on the product or extension cords as this

may damage the wire insulation.

m) Do not cover the product with cloth, paper or any material not part of the

product when in use.

n) Do not move the tree by pulling the tree tips or tree branches.

o) Read and follow all instructions that are on the product or provided with

the product.

SAVE THESE INSTRUCTIONS.

CAUTION! – ALWAYS UNPLUG YOUR TREE

FROM ITS POWER SOURCE BEFORE ASSEMBLING OR

DISASSEMBLING.

CAUTION

1. The product consists of non-replaceable LED lamps. To reduce the

risk of fire or electric shock, do not attempt to replace lamps or modify

string.

This product can only be used with the original adapter, not other

brands of adapter.

9ft Jackson Fir Micro Dot Tree

SKU# 1006215461

Package Contents

A. Top Section

Qty: 1

B. UpperMiddle

Section

Qty:1

C. LowerMiddle

Section

Qty:1



D. Tree Bottom

Qty: 1

E. Standwithan

eyebolt

Qty:1

F. PowerCordwith

afootpedal

switch

Qty:1

G. Remote Control

Qty: 1

H. Latch

Qty:2



I. Threadedironlatch

Qty:2

J. Retainerwasher

Qty:4

Assembly

Assembling the tree stand

Step 1. Choose a location near a wall outlet.

Step 2. Open the stand to a 90 degree angle until the hole lines up with the

hole on the tube.

Step 3. Screw an eye bolt into the hole.

Pre-Assembly

Summary of content (3 pages)

PAGE 1
9ft Jackson Fir Micro Dot Tree SKU# 1006215461 Safety Information IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. a) b) This product is for indoor use only. The electrical rating 0.57 A 120 V 60 Hz. c) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
PAGE 2
Assembling the tree Please remove protective covers from the base of the pole for each tree section before assembling. Step 1. Insert tree bottom (D) into the tree stand and tighten the screw. (See Fig. 1) Step 2. Insert lower middle section (C) into the tree bottom (D). (See Fig. 2) Step 3. Insert upper middle section (B) into the lower middle section (C). (See Fig. 3) Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4) Step 5.
PAGE 3
Loose branches 1. If a branch of the tree in section A, B or C falls off, follow the steps below to reinstall it with a spare latch (H). 1) Place the branch into the slot of the bracket. 2) Insert a spare latch through the hole and use diagonal pliers (not included) to crimp the latch. (See Fig. A) 2. If a branch of the tree in section D falls off, follow the steps below to reinstall it with a spare threaded iron latch (I) and two retainer washers (J). 1) Place the branch into the slot of the bracket.