Instructions / Assembly

customer service number at 1-877-527-0313,
PNTGR72245MRL-G
LED20
Please follow the instructions below in order to properly assemble
and store your tree.
OUTDOOR TREE SCULPTURE
2. Determine the final display location before assembling the tree.
The tree must be placed on level ground. Place the tree base in
the desired location.
3. Insert pole “A” into the tree base. (Fig 2)
4. Insert pole “B” into pole “A” making sure the tab on pole “B” slides
into pole “A” (Fig 3a).
5. Insert pole “C” into pole “B” making sure the tab on pole “C”
slides into pole “B” (Fig 3b).
ASSEMBLY INSTRUCTIONS:
A step stool or ladder maybe needed.
2 people recommended for assembly.
Retain carton for storage.
1. Carefully remove all parts from the carton. Your tree should include
the following (Fig 1):
1 tree base
The 6’ tree will have 5 collapsible tree panel section
1 bottom support pole (A)
1 middle support pole (B)
1 top support pole (C)
1 spire
4 Lawn stakes
Replacement LED bulbs and light clips
Fig 1
Tree base
Collapsible
tree panel
section
Replacement
LED bulbs and
light clips
Support poles
Spire
Lawn stakes
6. Separate each panel unfolding all 5 panels (Fig 4 a, b, c).
NOTE: The tree’s 5 panels will be electrically connected by male
and female coaxial connections (Fig 10). The base of the tree will
have (2) of these coaxial connection points labeled #2 and #4.
The top of the tree will also
have (2) coaxial connection
points labeled #1 and #3.
NOTE: It is important that
when hanging each
individual panel unto the
center support pole that
the two (#2) labeled
pairings of the panels are
together, as well as the (#4)
labeled pairings of the
panels are together, in
order to make the proper
connection points. (The 5th
panel will have no
numbered label; as it
possesses the trees plug).
A
Fig 2
Fig 4a
10. Proceed to make the (4)
necessary male and female
connections in order to
electronically connect the tree
panels.
11. Place the spire on top of the
tree. (Fig 8)
12. Proceed to take the loose string
of lights located at the top of
one of the tree’s panels and
begin wrapping and clipping
the light string to the spire.
Fig 4b Fig 4c
Fig 6
Fig 7
7. Take the 1st panel, (that
possesses the trees plug), and
starting from the top of the
pole to the bottom insert the 4
prongs into the 4
corresponding eyelets (Fig 5).
8. Proceed in hanging the
remaining 6 panels
(6’-remaining 4 panels) in the
same manner as the above;
noting that the lower pane
pairings of #2 to #2 and #4 to
#4 must be aligned next to
each other (Fig 6).
9. Secure the positioning of each
panel by sliding the base of
each panel into the slots
provided on the top of the
trees base (Fig 7).
Fig 5
Fig 8
B
A
Fig 3a
C
B
Fig 3b
Fig 10
Check the item for any loose, unlit or damaged bulbs.
1. Failure to light; unplug the product and check to see that
the GFCI outlet is functioning.
2. A section fails to light; leave the product plugged in and
check all light string connections. This product uses low
voltage coaxial connections. To connect the light strings;
align the male end to the female connectors as shown
and connect them together. Slide the cover from the
“male” connector over the “female” connector and tighten
(Fig 10).
NOTE: Replacement bulbs are provided; this is a specialty
LED bulb. Do not attempt to replace with a standard LED or
incandescent bulb. Should you require additional bulbs
please contact our customer service department.
TROUBLESHOOTING
1. Leave assembled if storage room permits or disassemble,
placing all components in the original carton.
2. Store in cool, dry location away from sunlight.
DISASSEMBLY & STORAGE
Fig 9
13. Push the wire stakes into the ground securing the tree
base. Angle each stake 45 degrees toward the center of
the tree (Fig 9).
You have completed the assembly of the tree.
14. To illuminate fully insert the plug into a working GFCI outlet
or an outdoor rated extension cord.
Made in China
Printed in China
This is not a toy, for decorative use only.
Item No.
15”
11.5”
In the event that you should encounter any
issues; please refer to the “Troubleshooting”
portion of this manual or call our toll free
and a trained representative will assist you.