Instructions / Assembly

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a)
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
poper installation.
c) This seasonal use product is not intended for permanent installation
or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles
or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
h) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of
the product when in use.
m) This product is equipped with push-in type lamps. Do not twist
lamps.
n) This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided
with the product.
p) SAVE THESE INSTRUCTIONS.
Use and Care Instructions
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the
needles are brown or break off easily. Keep the tree holder filled
with water.
b) If the product is placed on a tree, the tree should be well secured
and stable.
c) Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or cords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
50L LED WARM WHITE LIGHT SET
SKU# 1004350871
d) When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress on the product conductors, connections,
and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
User Servicing Instructions
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover
on top of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided
with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
b) Unlock the burned out LED bulb by lifting the hook and pulling both
the bulb and plastic base straight out of the bulb holder. Do not twist
bulbs.
c) Replace burned out bulb with 3.0 volt 0.06 watt LED type bulb ONLY.
(Replacement bulbs included)
d) Lock the LED bulb.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1. Pull the reflector out.
2. Remove the base of burned out lamp by straightening lamp leads
and gently pulling lamp out.
3. Thread leads of new lamp through hole in old base with one lead in
each hole (always match the long lead of new lamp to the hook of
lamp base.)
4. After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5. Insert the reflector into the base.