Item #XXX XXX Model #AL14-22-BN USE AND CARE GUIDE BENTLEY III 22 INCH CEILING FAN Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.
Table of Contents Table of Contents .......................................................... 2 Disassembling Your Fan ............................................. 13 Safety Information ......................................................... 3 Operation ..................................................................... 14 Remote Control Operating Instructions ..................................14 Installing the Remote Control Holder ..................................... 14 Warranty ...............
Safety Information 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs.
Warranty We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. We also warrant that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size unless noted otherwise in the table below.
Pre-Installation (continued) PACKAGE CONTENTS A G B H C I D E J F K L Part Description Quantity Part Description Quantity A Mounting bracket (preassembled) 1 G Rear guard (preassembled) 1 B Canopy 1 H Blade (preassembled) 1 C Canopy bottom cover (preassembled) 1 I Front guard (preassembled) 1 D Hanger ball/downrod assembly 1 J Receiver 1 E Coupling cover 1 K Remote control 1 F Motor head (preassembled) 1 L Remote control holder 1 6
Installation MOUNTING OPTIONS WARNING: To reduce the risk of fire, electric shock, or other personal injury, mount the fan only on an outlet box or supporting system marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
Assembly 1 2 Preparing the canopy Preparing the motor □ Remove the canopy bottom cover (C) from the canopy (B) by turning the canopy bottom cover (C) counterclockwise. □ Remove the clevis pin (EE), cotter pin (FF), and loosen the two collar setscrews (AA) at the top of the motor head (F) collar.
Assembly — Hanging the Fan 4 5 Installing the mounting bracket to the electrical box □ WARNING: To reduce the risk of fire, electric shock, or other personal injury, mount the fan only on an outlet box or supporting system marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. □ Pass the 120-volt supply wires through the center hole in the mounting bracket (A).
Assembly — Hanging the Fan (continued) Preparing the receiver and remote control 7 WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. K J This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units.
Assembly — Hanging the Fan (continued) WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. NOTE: The fan must be installed at a maximum distance of 20 ft. from the remote control for proper signal transmission between the remote control and the fan's receiving unit.
Assembly — Hanging the Fan (continued) 9 10 Installing the canopy WARNING: Make sure the tab on the mounting bracket (A) properly sits in the groove in the hanger ball/downrod assembly (D) before attaching the canopy (B) to the mounting bracket (A) by turning the canopy until it drops into place. □ Tuck the connections neatly into the ceiling outlet box (NN).
Disassembling Your Fan This fan comes with a pre-assembled the rear guard (G), blade (H), and front guard (I) for your easy installation. Check that all screws are tight and securely in place. If you need to disassemble the fan for any reason such as cleaning, follow these steps below: □ Loosen the front guard screws (II) to disassemble the front guard (I) from the rear guard (G). □ Remove the blade cover (JJ) from the blade (H) by turning the blade cover (JJ) clockwise.
Operation REMOTE CONTROL OPERATING INSTRUCTIONS □ Install the 12V MN21/A23 battery (KK) (included) into the remote control (K). To prevent damage to the remote control (K), remove the battery if not used for long periods. □ Restore power to the ceiling fan and test for proper operation. K HI , MED, LOW buttons: Sets the fan speed. KK OFF button: Turns the fan off.
Care and Cleaning Do □ Do not Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. Because of the fan’s natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling. □ Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
Service Parts A AA G GG B H BB C CC I D HH II DD JJ E J EE F KK K LL FF L Part Description Part Description A Mounting bracket (preassembled) AA Collar setscrew (preassembled) B Canopy BB Plastic wire nut C Canopy bottom cover (preassembled) CC Canopy mounting bracket screw (preassembled) D Hanger ball/downrod assembly DD Remote control holder mounting screw E Coupling cover EE Clevis pin (preassembled) F Motor head (preassembled) FF Cotter pin (preassembled) G R
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Retain this manual for future use.