Item # 1007 796 646 Model # FHTM80273 USE AND CARE GUIDE ST. CHARLES RECTANGULAR LP FIRE PIT Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this fire table.
Table of Contents Planning Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Hardware Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Care and Maintenance . . . . . . . . . . . .
Safety Information (continued) WARNING: Fire table is for outdoor use only. Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners and circulating air passageways of the appliance are kept clean.
Safety Information (continued) The use of alcohol, prescription or non-prescription drugs may impair an individual’s ability to properly assemble or safely operate this outdoor fire table. DO NOT use in an explosive atmosphere. Keep gas fire table area clear and free from combustible materials, such as gasoline. This outdoor fire table is not to be installed or used in or on recreational vehicles and/or boats. Always use in accordance with all applicable local, provincial and national codes.
Safety Information (continued) ATTENTION: Any alteration of the outdoor fire table that is not specifically directed in the operations manual will void manufacturer warranty. PROPANE (LP) DANGERS AND WARNINGS LP GAS LP gas is flammable and hazardous if handled improperly. Familiarize yourself with its hazards before using any LP gas product. PROPANE HAZARDS Flammable, explosive under pressure, heavier than air and settles in pools in low areas. In its natural state, propane has no odor.
Safety Information (continued) HOSE AND REGULATOR ASSEMBLY AND REPLACEMENT This fire table comes equipped with a standard LP gas hose and regulator including the appliance side connection for a CGA No. 791 Cylinder Connection Device. The LP gas hose and regulator supplied with this fire table must be used. Only a hose and regulator specified by manufacturer can be used for replacement. The CGA No.
Warranty 1 YEAR FRAME LIMITED WARRANTY WHAT IS COVERED We warrant the frames to be free of manufacturing defects to the original purchaser for one year. WHAT IS NOT COVERED It remains the customer’s responsibility for freight and packaging charges to and from our service center. This warranty does not cover commercial use, hardware, acts of nature, fire, freezing and abusive use. In addition, purchased parts are not covered under this warranty.
Pre-assembly (continued) HARDWARE INCLUDED NOTE: Hardware not shown to actual size.
Pre-assembly (continued) PACKAGE CONTENTS S M N O B L R E P Q I E J G F K T D A Part H Description C Quantity A Knob 1 B C Table Top Right Front Leg Left Front Leg 1 1 Rear Leg Right Side Panel Left Side Panel 2 2 Door Back Panel Limit Tube 1 1 1 1 M Tank Support Glass Beads Rectangular Burner Bowl N Burner Ring 1 O Pilot Housing 1 P Manual Electric Igniter 1 Q 1 R Control Knob Regulator/Hose 1 S Burner Lid 1 T AAA Battery 1 D E F G H I J K L WARNING: F
Assembly 1 Attaching the Legs to the Table Top NOTE: Pay attention to the direction of switch knob and the legs, it must place as below direction. Place the table top (B) upside down on a soft surface. Attach the right front leg (C) and left front leg (D) to the table top (B) using M6x15 combination bolts (AA), as shown below. Do not tighten the bolts at this step. AA AA NOTE: Loosely tighten all the bolts using hex wrench (EE).
Assembly (continued) 3 Attaching the Limit Tube to the Left Side Panel and Right Side Panel Attach the limit tube (J) to the left side panel (G) and right side panel (F) using M6x15 combination bolts (AA), as shown below. Do not tighten the bolts at this step. AA NOTE: Loosely tighten all the bolts using hex wrench (EE). G F J 4 Connecting the Tank Support Connect the tank support (K) to the right front leg (C), left front leg (D) and rear legs (E) using M6x15 combination bolts (AA).
Assembly (continued) 5 Connecting the Door Connect the door (H) to the left front leg (D) using a plastic washer (CC). Connect the door (H) to the tank support (K) using M6x12 countersunk bolt (BB) and a plastic washer 2 (DD). Once all the bolts are in place, fully tighten all the bolts using the hex wrench (EE). BB DD K D CC H 6 Attaching the Knob to the Door and Checking the Table Turn the assembled fire table right side up. Attach the knob (A) to the door (H) and tighten it clockwise.
Assembly (continued) 7 Placing the Glass Beads CAUTION: To ensure proper function, the screen on the pilot housing should be free of glass beads. Place the glass beads (L) into the rectangular burner bowl (M). L Pilot Housing M Burner Tube do not block opening CORRECT INCORRECT Screen 8 Placing the Burner Lid WARNING: Surfaces on the fire table can remain extremely hot for a period after use. Allow 45 minutes to cool down before touching or moving the fire table.
Operation 1 Installing the LP Gas Tank CAUTION: LP gas tank must be properly disconnected and removed prior to moving this outdoor fire table. Make sure LP gas tank valve is closed. To operate, you will need one precision-filled standard grill LP gas tank with external valve threads Loosen LP gas tank retainer bolt by turning counterclockwise. Place precision-filled LP gas tank upright into hole in outdoor fire table base so the tank value is facing the gas line connection.
Operation (continued) 3 Disconnecting the LP Gas Tank NOTE: The LP gas tank must be properly disconnected and removed prior to moving the fire table. Before disconnecting make sure the LP gas tank valve is “CLOSED”. Disconnect regulator/hose assembly from LP gas by turning knob counterclockwise until it is loose. Place the protective cap cover on the LP gas tank and store it outdoors in a well-ventilated area out of direct sunlight.
Operation (continued) 5 Tank/Gas Line Connection Leak Test Make 2-3 oz. of leak detection solution by mixing one part liquid dishwashing soap with three parts water. Make sure the control knob is in the “OFF” position. Connect LP gas tank per “CONNECTING LP GAS TANK” section. Turn LP gas tank valve to “OPEN”. Using a spoon or a squirt bottle, pour several drops of solution over each spot marked “X”. a. If any bubbles appear, turn LP gas tank valve to “CLOSED”, reconnect and re-test. b.
Operation (continued) 7 Close the Door Close the door (H). Now the fire table is complete and ready to use. H 17 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Operation (continued) CAUTION: Failure to follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury or damage to property. WARNING: Never light burner with the cover on the outdoor fire table. CAUTION: Keep outdoor gas appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. CAUTION: Do NOT obstruct flow of combustion and ventilation air. 7.87-11.81in. 20-30 cm.
Operation (continued) LIGHTING (CONTINUED) 11. If igniter does not light burner: a. Wearing heat-resistant gloves, position a long, lit match or long, lit butane lighter near the pilot housing. b. Push and turn control knob to “ON”. c. Remove match/lighter once burner is lit. 12. After lighting, observe the burner flame and make sure all burner ports are lit and flame height matches illustration on page 18.
Care and Maintenance Cleaning Surfaces Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water. For stubborn stains, use a citrus-based cleaner and a nylon scrubbing brush. Rinse clean with water. Allow to air dry. Before Storing Turn LP gas tank valve to “CLOSED”. Turn control knob to the “OFF” position. NOTE: A “poof” sound is normal as the last of the LP gas is burned. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section. Clean all surfaces.
Troubleshooting Problem Possible Cause Solution The LP gas tank valve is closed. Make sure that the regulator is securely attached to the LP gas tank per the "Installing the LP Gas Tank" section. Then turn the LP gas tank valve to "OPEN." The LP gas tank is low or empty. Exchange, refill or replace the LP gas tank. Turn the LP gas tank valve to “CLOSED”. Wait 5 minutes for the gas to clear. Follow the steps in the “Checking for Leaks and Burner Connections” section. The LP gas leaks.
Troubleshooting (continued) The tank is out of gas. There is a sudden drop in gas flow, or the flame height is reduced. The overfilling prevention device may have been activated. There is an irregular flame pattern, or the flame does not run There is no gas flow. the full length of the burner. The flame is yellow or orange. Turn control knob to “OFF”. Wait 30 seconds and light the outdoor fire table per the “Lighting” section.
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Retain this manual for future use.
Item # 1007 793 241 Model # FZM71027-STC USE AND CARE GUIDE ST. CHARLES 6PK DINING CHAIR Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this chair.
Pre-Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Planning Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Swivel Chair Package Contents . . . . . . . . . . . . . . . . . . . . . . . 4 Stationary Chair Package Contents . . . . . . . . . . . . . . . . . . . . 5 Swivel Chair Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty YEAR FRAME AND FABRIC LIMITED WARRANTY WHAT IS COVERED We warrant the frame and fabric to be free of manufacturing defects to the original purchaser for five years. WHAT IS NOT COVERED It remains the customer’s responsibility for freight and packaging charges to and from our service center. This warranty does not cover commercial use, hardware, acts of nature, freezing and abusive use. In addition, purchased parts are not covered under this warranty.
Pre-assembly (continued) HARDWARE INCLUDED NOTE: Hardware not shown to actual size.
Pre-assembly (continued) STATIONARY CHAIR PACKAGE CONTENTS A B K J L H I Part A B H I J K L Description Support Bar Backrest Back Cushion Seat Cushion Stationary Chair Left Arm Stationary Chair Right Arm Stationary Chair Seat Quantity 4 4 4 4 4 4 4 5 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Swivel Chair Assembly the Support Bar, Backrest and Swivel Chair Seat into the Swivel Chair 1 Inserting Left Arm Place the swivel chair left arm (C) on a soft surface. Insert the support bar (A), backrest (B) and swivel chair seat (E) into the swivel chair left arm (C).
Swivel Chair Assembly (continued) 2 Attaching the Swivel Chair Seat to the Swivel Chair Left Arm Attach the swivel chair seat (E) to the swivel chair left arm (C) using M6x30 combination bolts (AA). Do not tighten all bolts at this step. NOTE: Loosely tighten all the bolts using hex wrench (DD). E AA C 7 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Swivel Chair Assembly (continued) 3 Inserting the Swivel Chair Right Arm into the Support Bar, Backrest and Swivel Chair Seat Insert the swivel chair right arm (D) into the support bar (A), backrest (B) and swivel chair seat (E).
Swivel Chair Assembly (continued) 4 Attaching the Swivel Chair Right Arm to the Swivel Chair Seat Attach the swivel chair right arm (D) to the swivel chair seat (E) using M6x30 combination bolts (AA). Do not tighten all bolts at this step. NOTE: Loosely tighten all the bolts using hex wrench (DD). D E AA 9 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Swivel Chair Assembly (continued) 5 Connecting the Support Bar to the Arms Turn the swivel chair right side up. Connect the support bar (A) to the swivel chair left arm (C) and swivel chair right arm (D) using M6x20 bolts (CC). Once all of the bolts are in place, fully tighten all the bolts using the hex wrench (DD).
Swivel Chair Assembly (continued) 6 Attaching the Support Tube to the Swivel Chair Seat Place the swivel chair upside down on a soft surface. Attach the support tube (F) to the swivel chair seat (E) using M8x20 combination bolts (BB). Fully tighten all the bolts using the wrench (EE). BB BB E F 11 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Swivel Chair Assembly (continued) 7 Inserting the Support Tube into the Swivel Base Insert the support tube (F) into the swivel base (G).
Swivel Chair Assembly (continued) 8 Placing the Seat Cushion and Back Cushion on the Swivel Chair Place the seat cushion (I) and back cushion (H) on the swivel chair. Ensure all conections are secure before use. H I 13 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Stationary Chair Assembly 1 Inserting the Support Bar, Backrest and Stationary Chair Seat into the Stationary Chair Left Arm Place the stationary chair left arm (J) on a soft surface. Insert the support bar (A), backrest (B) and stationary chair seat (L) into the stationary chair left arm (J).
Stationary Chair Assembly (continued) 2 Attaching the Stationary Chair Seat to the Stationary Chair Left Arm Attach the stationary chair seat (L) to the stationary chair left arm (J) using M6x30 combination bolts (AA). Do not tighten all bolts at this step. NOTE: Loosely tighten all the bolts using hex wrench (DD). L AA J 15 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Stationary Chair Assembly (continued) 3 Inserting the Stationary Chair Right Arm into the Support Bar, Backrest and Stationary Chair Seat Insert the stationary chair right arm (K) to the support bar (A), backrest (B) and stationary chair seat (L).
Stationary Chair Assembly (continued) 4 Attaching the Stationary Chair Right Arm to the Stationary Chair Seat Attach the stationary chair right arm (K) to the stationary chair seat (L) using M6x30 combination bolts (AA). Do not tighten all bolts at this step. NOTE: Loosely tighten all the bolts using hex wrench (DD). K L AA 17 HOMEDEPOT.COM/HOMEDECORATORS Please contact 1-800-986-3460 for further assistance.
Stationary Chair Assembly (continued) 5 Connecting the Support Bar to the Arms Turn the stationary chair right side up. Connect the support bar (A) to the stationary chair left arm (J) and stationary chair right arm (K) using M6x20 bolts (CC). Once all of the bolts are in place, fully tighten all the bolts using the hex wrench (DD).
Stationary Chair Assembly (continued) 6 Placing the Seat Cushion and Back Cushion on the Stationary Chair Place the seat cushion (I) and back cushion (H) on the stationary chair. Ensure all connections are secure before use. H I Care and Cleaning For best results, clean the chair with a damp cloth and dry thoroughly. This will help prevent mildew by removing dirt particles that may accumulate. Do not clean with abrasive materials, bleach, or solvents.
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-800-986-3460 HOMEDEPOT.COM/HOMEDECORATORS Retain this manual for future use.
