Use and Care Manual

6
Operation (continued)
4
Using the heater control
□
The heater button (4) turns the heater on or off. There is no speed setting for the heater blower. If the heater is on when t
he unit is turned off
by the main power button, when the power is turned back on, the heater will come on at the same time. If the heater is off when the main
power is off, the heater will remain off when main power is turned back on.
□ When the heating function turns on, press and hold the heater button (4) for five seconds to enter temperature adjustment mode. The LED
indicator is red. In adjustment mode, the display (1) flashes (interval is 0.5 second). There are 22 levels to change Fahrenheit temperature
72°F―73°F…82°F ―ON—62°F ―63°F …71°F. After this is set, the display (1) flashes five times. If idle, the display turns off after 10 seconds.
□ With the heater on, gently press and hold the main power button for five seconds to enter temperature converting mode. The LED indicator
flashes five times in red color then changes to green. In this converting mode, the display (1) flashes (interval is 0.5 second). Press and hold
the heater button (4) for five seconds to enter temperature adjustment mode. There are 12 levels to change Celsius temperature
22°C―23°C …27°C ―ON ―17°C ―18…21°C. After it is set, the display (1) flashes five times. If idle, the display turns off after 10 seconds.
Repeat the same process to convert Celsius temperature into Fahrenheit temperature.
□ To lock the heating function, with the main power button on, press and hold the heater button (4) for ten seconds. The log lights flash six
times to indicate that the heater function is locked. In this mode, there is no heating function but only glowing logs.
NOTE: After the heater function or power is shutoff the blower will continue to run for several minutes to cool the internal components.
□ To unlock the heating function, press and hold the heater button (4) for ten seconds. The log lights flash six times and then enter heating
function mode.
5
Using the flame control
□
Press the flame button (5) to
set the flames for different levels of flame height. These flame levels are
shown
in the display
(1). The flame
settings are as follows:
Button Press
Flame Level
Display Value
Fireplace
Appearance
1st press
High
L4
Flames Highest, Logs Glow Highest
2nd
press
Medium
L3
Flames Medium, Logs Glow Medium
3rd press
Low
L2
Flames Low, Logs Glow Low
4th press
Flames Off
L1
Flames Off, Logs Glow Highest
5th press
All Off
None
Flames Off, Logs Off
□ Regardless of the previous flame setting, when powered off by the main power button, the flames will come on in L4 mode (High) when you turn
the heater on.
□ To lock the flame function, with the flame in L4 mode, press and hold the flame button (5) for five seconds. The log lights flash six times to
indicate that the flame function is locked. In this mode, there are no flames but only glowing logs. Pressing the flame button in sequence will set
the logs for different levels of log brightness. The logs brightness levels are shown in the display segment (1). The logs settings are as follows:
Button Press
Flame Level
Display Value
Fireplace Appearance
1st press
Flames Off
L4
Logs Glow Brightest
2nd press
Flames Off
L3
Logs Glow Medium
3rd press
Flames Off
L2
Logs Glow Low
4th press
Flames Off
L1
Logs Glow Brightest
5th press
All Off
None
Logs Off
□ To unlock the flame function, press and hold the flame button (5) for five seconds. The log lights flash six times and then both flame lights and log
lights turn on.
1
5
1
4