Instructions / Assembly

ManualsBrandsHome Plow by Meyer ManualsKitchen2 in. Class 3 Front Receiver Hitch Mount for 1992-2009 Ford Ranger

Parts List

DESCRIPTIONPART NUMBERQTYITEM

.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP12

CARRIAGE BOLT1/2-13 x 1 3/4

HEX FLANGE NUT

HFN 121343

1/2" FISHWIRE1_2 FISHWIRE

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

GROSS LOAD CAPACITY WHEN USED AS A STRAIGHT LINE PULL: 9,000 LBS. MAX. LINE PULL.

***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***

HITCH WEIGHT: LBS.

INSTALL TIME:

MINUTES

INSTALL NOTES:

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS

ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,

Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of

this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or

consequential loss or damage.

3,500

350

31019

5/7/2010

1) Lower plastic radiator shield. For 2WD Rangers, remove lower fascia.

2) Fishwire spacers and carriage bolts for forward attachment points into position.

3) Raise receiver into position, as far forward as possible, and install forward fasteners.

(Note: Slight trimming of bumper fascia may be necessary where it contacts receiver.)

4) Using receiver as guide, enlarge the rearmost holes in the frame.

5) Fishwire spacers and carriage bolts as shown for rearward attachment points.

6) Check clearance of transmission cooler line. Bend or tie back to prevent contact with receiver.

7) Torque all 1/2" fasteners to 50 lb.-ft.

ENLARGE EXISTING HOLES

FASCIA TRIMMING

SKID SHIELD REMOVAL

FRAME RAIL

ENLARGE HOLE

EXISTING SLOTS

FASCIA TRIM DIAGRAM

3.00 in

BUMPER FASCIA

FORD RANGER, MAZDA B- SERIES

(EXCLUDING MODELS WITH FRONT CROSS MEMBER)

Summary of content (2 pages)

PAGE 1
FORD RANGER, MAZDA B- SERIES 31019 (EXCLUDING MODELS WITH FRONT CROSS MEMBER) 5/7/2010 GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 3,500 LBS. TRAILER WEIGHT & 350 LBS. TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A STRAIGHT LINE PULL: 9,000 LBS. MAX. LINE PULL. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** Parts List ITEM 1 QTY 4 PART NUMBER CM-SP12 DESCRIPTION .250 x 1.00 x 2.
PAGE 2
FORD RANGER, MAZDA B-SERIES TRUCKS 31019 (EXCLUDING MODELS WITH FRONT CROSS MEMBER) ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***. FRONT MOUNTED ACCESSORIES 1) Do not exceed front axle Gross Weight Rating (GAWR). Consult owners manual or specification plate located on driver's door frame. Measure gross front axle weight by placing front wheels of loaded vehicle on a scale. WARNING: Exceeding GAWR may overload the front axle and/or suspension.