Downloadable Instruction Book

5
4
How to use the CLEAN Function: If you wish to change the type of soap in the Dispenser, you may use
the CLEAN function to empty and clean the unit. Open the Battery/Control Compartment door (Figure 2).
Press the CLEAN button and the unit will enter the auto cleaning mode. The motor will turn on and
pump for 30 seconds. During this period, you can press the CLEAN button again to abort the cleaning
function (motor will turn off). Repeat until there is no more soap in the reservoir. To thoroughly flush out
the unit, you should add water to the reservoir and repeat the cleaning process.
Note: Hold device over a sink or dish when running the Clean function, to prevent soap from spilling
onto counter.
IMPORTANT:
1. The Motion Detector that activates dispensing uses a sensitive infrared sensor. To avoid accidental
dispensing of soap, please do not place the Soap Dispenser in direct sunlight.
2. After a period of inactivity, the soap inside Soap Dispenser may become dry and clog the line.
Should this occur, simply use a toothpick or water to remove the obstruction.
3. The only part of the Soap Dispenser designed to be wet is the liquid reservoir and spout. Do not
immerse the Soap Dispenser in water as the product will be damaged.
4. Run the CLEAN Function to flush the liquid/soap reservoir with water and remove batteries from the
battery compartment whenever the Soap Dispenser is to be left unused for a long period of time.
5. To clean the unit, use a soft damp cloth. Do not clean with a abrasive materials or corrosive
substances.
6. The device is not designed to be held or tipped upside down when there is soap in the Reservoir.
Use caution to maintain the device on a level surface at all times.
7. Make sure your child understands that liquid soap solution is not for drinking and that it should be
kept away from the eyes.
Trouble Shooting:
No Soap Dispensed; Motor Does Not Run
1. Ensure that Soap Dispenser is turned on. Press and hold the POWER button for 3 seconds to turn
off. Press the POWER button once to turn ON.
2. Make sure hands are placed directly between the Motion Sensor and Spout.
3. Ensure that unit is not placed in bright sunlight, which will interfere with Motion Sensor operation.
4. Check that batteries are installed with correct polarity (+/–) and are not dead.
No Soap Dispensed; Motor Runs
1. During start-up you may need to activate the Motion Sensor several times to “prime” the pump to
begin dispensing soap.
2. The soap reservoir should be at least ¼ FULL.
3. Make sure that no dried soap is clogging the spout or pump tubing. Use a toothpick to clean the
spout if necessary.
No Audio/Song
1. If unit dispenses (motor runs) but does not play music, the SONG button has been turned OFF.
Make sure your hands are dry before opening the battery compartment. Open the battery
compartment and press the SONG button once to activate the SONG mode.
2. If unit does not dispense (motor does not run) or play audio, check batteries for proper positioning
and/or replacement.
Battery Precautions:
1. Use AA alkaline batteries only. Do not use rechargeable batteries.
2. Replace all batteries at the same time.
3. Clean the battery contacts and the contacts of the device prior to battery installation with a dry cloth.
4. Ensure the batteries are installed correctly with regard to polarity (+/–).
5. Remove batteries from the unit when it is not to be used for an extended period of time.
6. Remove depleted batteries from the unit promptly. Dispose of used batteries safely. Keep all
batteries away from children. Batteries are small objects and could be ingested. If swallowed,
contact a physician at once. Do not open batteries or dispose of in fire. Do not mix the new and
used batteries.
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.