Replacement Part List

ManualsBrandsHomelite ManualsAccessories15 in. EZ Clean Gas Pressure Washer Surface Cleaner

15 in. Surface Cleaner Attachment

AEZ31023

WARNING:

To reduce the risk of injury, user must read and understand

the operator’s manual for their pressure washer before us-

ing this accessory. To reduce the risk of injury or property

damage, spray the pressure stream in a safe direction to

ensure proper connection of all accessories before starting

any cleaning project. Fits most pressure washers. Ensure

compatibility and proper fit before using this accessory.

Wear eye protection with side shields marked to comply

with ANSI Z87.1. Risk of fluid injections; do not point at

people, pets, electrical devices or the unit itself. Turn off the

pressure washer before changing or adjusting accessories.

For cold water use only. Save these instructions. Refer to

them frequently and use them to instruct other users. If you

loan someone this tool, loan them these instructions also.

PRODUCT SPECIFICATIONS

Connections ..................................1/4 in. Quick Connect Plug

Deck Width ...................................................................... 15 in.

Maximum Pressure ..................................................... 3300 psi

Maximum Water Flow .....................................................3 gpm

Maximum Water Temperature .........................................140°F

Weight ........................................................................ 4.75 lbs.

INSTALLING THE SURFACE CLEANER ON

THE SPRAY WAND

See Figure 1.

Insert the surface cleaner inlet plug into the spray wand quick

connect coupler and secure.

WARNING:

To reduce the risk of injection or injury, only use the surface

cleaner on flat, horizontal surfaces. Never lift the surface

cleaner from the cleaning surface while operating the pres-

sure washer.

USING THE SURFACE CLEANER

See Figure 2.

n Once the surface cleaner is installed, connect the hose to

the pressure washer as described in your pressure washer

manual.

n Start the pressure washer as described in your pressure

washer manual.

n Walk slowly behind the cleaning deck, cleaning as you go.

NOTE: If striping or swirling occurs, slow your pace. If strip-

ing or swirling continues, the surface cleaner nozzle(s) may

be clogged. See Nozzle Maintenance for how to clean the

nozzles.

Fig. 1

INLET

PLUG

Fig. 2

QUICK CONNECT

COUPLER

WARNING:

Striking any raised obstacle while using the surface cleaner

will damage the unit. If contact does occur and causes

vibration when operating the pressure washer, stop and

discontinue use. Continuing to operate the unit could result

in serious injury or damage to the unit.

NOTE: See figure 3 for the location of the spray bar.

NOZZLE MAINTENANCE

See Figure 3.

When shipped, two nozzles are pre-assembled to the surface

cleaner. These nozzles are appropriate for use with pressure

washers operating at 2300 to 3300 psi with a maximum flow

rate of 3.0 gpm.

Summary of content (6 pages)

PAGE 1
5 in. Surface Cleaner Attachment AEZ31023 WARNING: To reduce the risk of injury, user must read and understand the operator’s manual for their pressure washer before using this accessory. To reduce the risk of injury or property damage, spray the pressure stream in a safe direction to ensure proper connection of all accessories before starting any cleaning project. Fits most pressure washers. Ensure compatibility and proper fit before using this a ccessory.
PAGE 2
Excessive pump pressure (a pulsing sensation felt while squeezing the trigger and/or a higher vibration in the surface cleaner) may be the result of a clogged or dirty nozzle. n Turn off the pressure washer and shut off the water supply. With the surface cleaner on the ground, pull trigger to release water pressure. n Disconnect surface cleaner from spray wand. n Using a straightened paper clip or nozzle cleaning tool (not provided), free any foreign materials clogging or restricting the nozzle.
PAGE 3
Accessoire de 381 mm (15 po) pour nettoyeur de surface AEZ31023 AVERTISSEMENT : Pour réduire les risques de blessure, l’utilisateur doit lire et comprendre le manuel d’utilisation de sa laveuse à pression avant de l’utiliser. Pour réduire les risques de blessures ou de dommages matériels, diriger le jet dans une direction sécuritaire pour vérifier que tous les accessoires sont bien branchés avant de commencer le nettoyage. Convient à la plupart des laveuses à pression.
PAGE 4
Si la buse est bouchée ou sale, cela peut créer une pression excessive au niveau de la pompe (une vibration est ressentie en appuyant sur la gâchette et/ou une vibration plus importante sur la surface de la pompe). n Éteindre la laveuse à pression et couper l’alimentation en eau. Placer le nettoyeur de surface sur le sol et appuyer sur la gâchette pour relâcher la pression d’eau. n Débrancher le nettoyeur de surface de la lance d’arrosage.
PAGE 5
Accesorio para limpiador de superficie de 381 mm (15 pulg.) AEZ31023 ADVERTENCIA: CLAVIJA DE ENTRADA DE LA UNIDAD COLLARIN ACCÍONADO POR RESORTE Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador de la lavadora de presión antes de usar este accesorio. Para reducir el riesgo de lesiones o daños a la propiedad, rocíe el chorro de presión en una dirección segura para asegurar que la conexión de todos los accesorios sea correcta antes de utilizar la unidad.
PAGE 6
n Apague la lavadora de presión y cierre el suministro de agua. Apunte la boquilla hacia una dirección segura y oprima el gatillo para purgar el agua. n Desconecte el limpiador de superficie del tubo rociador. TUBO ROCIADOR n Con un clip para papel abierto o una herramienta para limpiar boquillas (no viene incluida), libere la boquilla de las obstrucciones producidas por material extraño.