5020-941 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Patent 8,584,600 B2 Part List B. Side Panel 1 pc. C. Side Panel 1 pc. D. Middle Panel 1 pc. E. Front Rail 1 pc. H. Back Rail 1 pc. F. Front Rail 1 pc. I. Shelf 4 pcs. G. Back Rail 1 pc.
Assembly Instructions 2/9 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/9 STEP 3 E Attach Middle Panel (D) to Back Rails (G), (H) and Back Upright (L) with Cam Locks. (See Figure 3) F Slide Back Panels (K) into position. Attach Front Rails (E) and (F) to unit with Cam Locks. Cam Lock D G K L K H Figure 3 Cam Lock B C STEP 4 Attach Side Panels (B) and (C) to unit with Cam Locks.
Assembly Instructions 4/9 Flat Washer Head Cap Bolt STEP 5 Attach Base (J) to unit with Cam Locks, Flat Washers and Head Cap Bolts. Tighten bolts with Hex Wrench. (See Figure 4) J Cam Lock STEP 6 Figure 4 P Turn unit to its upright position. Attach Post Assemblies (P) and (Q) to unit with Head Cap Bolts. Tighten bolts with Hex Wrench.
Assembly Instructions 5/9 3/4” Round Head Screw M N Knob Machine Screw STEP 7 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 5) Note: Unit must be level to proceed. Insert 3/4” Round Head Screws into pre-drilled holes in back of unit, then tighten. Note: Unit must be level before tightening these screws. Attach Doors (M) and (N) to unit by sliding door hinges into side panel hinges. (See Figure 6) Attach Knobs to Doors (M) and (N) with Machine Screws.
Assembly Instructions 6/9 Adjustable Pin STEP 8 Insert Adjustable Pins into side panels and middle panel at desired level. Slide Shelves (I) into position. I I I I STEP 9 3/4” Flat Head Screw Place Top (A1) and Leaf Top (A2) upside down on a soft cloth. A2 Attach Leaf Top (A2) to Top (A1) with 3/4” Flat Head Screws into pre-drilled holes.
Assembly Instructions 7/9 Drawer (O) O1 STEP 10 Attach Drawer Front (O1) and Drawer Back (O2) to Drawer Side (O3) with 1” Round Head Screws. O3 O2 Roller at back 1” Round Head Screw 1” Round Head Screw STEP 11 Slide Drawer Bottom (O5) into groove. O4 O5 Attach Drawer Side (O4) to unit with 1” Round Head Screws. Machine Screw STEP 12 Attach Knob with Machine Screw. Knob Part List O1. Drawer Front 2 pcs. O2. Drawer Back 2 pcs. O3. Drawer Side 2 pcs. O4. Drawer Side 2 pcs. O5.
Assembly Instructions 8/9 A1 Flat Washer Head Cap Bolt O O STEP 13 Attach Top (A1) to unit with Flat Washers and Head Cap Bolts. Slide Drawers (O) into position.
Assembly Instructions 9/9 STEP 14 When leaf top is down, it should be oriented vertically. If it is not vertical and adjustment is desired, turn the adjuster on adjuster block on back rail. (See Figure 9) Adjuster Block Figure 9 Top Extension Instructions STEP 15 Lift up leaf top. STEP 16 Holding leaf top up, pull out a back post from unit; then pull out other back post. Note: Unit must be level to work properly.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
5020-942 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Patent 8,584,600 B2 Part List P. Post Assembly 1 pc. Q. Post Assembly 1 pc. For assembly see instructions in carton 5020-941. homestyles Customer Service: www.homestylesfurniture.
5008-943 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Patent 8,584,600 B2 Part List A2. Leaf Top 1 pc. A1. Top 1 pc. For assembly see instructions in carton 5006-941, 5008-941 or 5020-941. homestyles Customer Service: www.homestylesfurniture.
5020-89 Bar Stool IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Seat 1 pc. E. Side Stretcher 1 pc. B. Leg 1 pc. F. Side Stretcher 1 pc. C. Leg 1 pc. G. Front Stretcher 1 pc. D. Back Frame 1 pc. Hardware List Hex Wrench 1 pc. Flat Washer 11 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not tighten all the bolts until each part is properly assembled. Keep Hex Wrench as the bolts may need to be tightened in the future. Wood Screw Flat Washer Spring Washer Head Cap Bolt C B G F E A STEP 1 Place Seat (A) upside down on a soft cloth. Attach Legs (B) and (C) to Seat (A) with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
Assembly Instructions 3/3 Head Cap Bolt (long) Spring Washer Flat Washer Wood Screw Head Cap Bolt (short) Spring Washer Flat Washer D STEP 2 Attach Back Frame (D) to unit with Flat Washers, Spring Washers, Head Cap Bolts (short) and Head Cap Bolts (long), tightening bolts only halfway. (See Figures 3 and 4) Tighten all bolts used in Steps 1 and 2. Insert Wood Screws into pre-drilled holes in unit, then tighten.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
