Assembly Instructions

ManualsBrandsHomestyles ManualsCabinets & ArmoiresHomestyles Barnside Gray Bar

Hardware List

Part List

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Tool(s) required for assembly: Phillips screwdriver, Level

20 05053 0098

Bar

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Middle Panel

1 pc.

Shelf

1 pc.

Front Rail

1 pc.

Top

1 pc.

Back Rail

1 pc.

Back Rail

1 pc.

Front Rail

1 pc.

Side Panel

2 pcs.

Upright

1 pc.

Panel

2 pcs.

Side Frame

1 pc.

Side Frame

1 pc.

Adjustable Pin

16 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

M3x12

Wood Screw

24 pcs. (+1 extra)

M6x16

Head Cap Bolt

26 pcs. (+1 extra)

Spring Washer

26 pcs. (+1 extra)

Flat Washer

26 pcs. (+1 extra)

M6x45

Tapered Bolt

2 pcs. (+1 extra)

M3.5x30

Wood Screw (long)

1 pc. (+1 extra)

Shelf

4 pcs.

Base

1 pc.

Summary of content (6 pages)

PAGE 1
20 05053 0098 Bar IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List F. Front Rail 1 pc. A. Top 1 pc. G. Back Rail 1 pc. B. Shelf 1 pc. H. Back Rail 1 pc. K. Side Frame 1 pc. L. Side Frame 1 pc. M. Upright 1 pc. N. Panel 2 pcs. C. Shelf 4 pcs. D.
PAGE 2
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Make sure unit is level before tightening these screws. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Wood Screw Attach Side Frames (K) and (L) to Side Panels (I) with Wood Screws.
PAGE 3
Assembly Instructions 3/5 STEP 3 Attach Shelf (B) to unit. Attach Base (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. B D Flat Washer Spring Washer Head Cap Bolt STEP 4 Attach Middle Panel (J) to unit with Wood Screw (long). Attach Side Frame (K) to unit with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in Steps 2, 3 and 4.
PAGE 4
Assembly Instructions 4/5 STEP 5 Turn unit to it’s upright position. N Attach Panels (N) to unit with Wood Screws. N Wood Screw STEP 6 Insert Adjustable Pins into side panels and middle panel at desired level. (See Figure 4) Place Shelves (C) into position.
PAGE 5
Assembly Instructions 5/5 STEP 7 Attach Top (A) to unit with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts. A Flat Washer Spring Washer Head Cap Bolt STEP 8 Level unit by adjusting the adjustable levelers on bottom of unit.
PAGE 6
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.