20 06661 0030 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. C. Stretcher 4 pcs. B. Leg 4 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Cap Nut Spring Washer Flat Washer Bolt Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3) Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 3 STEP 3 Turn table over to its upright position. Cover Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06661 0032 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. D. Shelf 2 pcs. B. Leg 4 pcs. C. Stretcher 4 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Cap Nut Spring Washer Flat Washer Bolt Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3) Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 3 STEP 3 Turn table over to its upright position. Cover Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06661 0053 Swivel Arm Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Back 1 pc. C. Arm 1 pc. D. Arm 1 pc. B. Seat 1 pc. E.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. Keep Wrench as the bolts and nuts may need to be tightened in the future. STEP 1 Attach Seat (B) to Back (A) with Flat Washers (large), Spring Washers (large) and Head Cap Bolts (long), tightening bolts only halfway.
Assembly Instructions 3/3 C D Flat Washer Spring Washer Head Cap Bolt (short) E STEP 3 Place unit onto Base (E). Attach Arms (C) and (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts (short), tightening bolts only halfway. Tighten all Head Cap Bolts used in Steps 1 and 3.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06661 0080 Arm Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List D. Arm 1 pc. C. Arm 1 pc. A. Back 1 pc. E. Leg 4 pcs. B. Seat 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/3 C D Flat Washer Spring Washer Head Cap Bolt (short) Figure 2 STEP 3 Turn unit to its upright position. Attach Arms (C) and (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts (short), tightening bolts only halfway. Tighten all Head Cap Bolts used in Steps 1, 2 and 3. Level unit by adjusting the adjustable levelers on bottom of legs.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
88 5561 37 Dining Table IMPORTANT NOTE This product is made from sturdy, high quality aluminum and will provide years of enjoyment. Do not use power tools to assemble and only tighten bolts until they are snug. Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts.
Assembly Instructions 2/2 IMPORTANT * Please keep Key Wrench in a safe place as you may need to tighten up the Nuts in the future. * Use a soft cloth between these parts and the floor. * Do not use power tools to assembly and do not tightening the bolts and nuts. * Do not tighten up all the bolts and nuts until each part is properly assembled. * After assembly item must be level to work properly. Use the included adjustable levelers to level.
