TrueEase Wiring Instructions

ManualsBrandsHoneywell ManualsHumidifiersTrueEASE 17 Gallon Per Day, Bypass Humidifier

Table Of Contents

INSTALLATION ADDENDUM

69-2576-05

Wiring Configuration

ADVANCED MODELS (HE150/HE250/HE300)

Fig. 1. Wiring HumidiPRO (H6062) to humidify only with a call for Heat or Fan.

Fig. 2. Wiring TrueIAQ, VisionPRO IAQ, or Prestige, using the intelligent

control to program humidity calls with heat, cool, or on demand.

HumidiPRO

M35152

POWER IN

G OR W

AIR PROVING

DEVICE

HE150/HE250 USES A 15 VA TRANSFORMER WIRED INTO 24V IN.

HE100/HE200 USES A 10 VA TRANSFORMER WIRED INTO 24V IN.

HE300 USES A LINE CORD PLUG.

CONNECT G TO HUMIDIFY WHEN THERE IS A FAN CALL.

CONNECT W TO HUMIDIFY WHEN THERE IS A HEAT CALL.

NEVER CONNECT BOTH. CONNECT C WHEN USING G OR W.

USE AIR PROVING DEVICE INSTEAD OF THE G/W CONNECTION

TO HUMIDIFY ANY TIME THE FAN IS OPERATING.

LEFT

OUTDOOR

SENSOR

M35153

FROM

HUMIDITY

CONTROL

POWER IN

HE150/HE250 USES A 15 VA TRANSFORMER WIRED INTO 24V IN.

HE100/HE200 USES A 10 VA TRANSFORMER WIRED INTO 24V IN.

HE300 USES A LINE CORD PLUG.

RIGHT

LEFT

Summary of content (4 pages)

PAGE 1
Wiring Configuration INSTALLATION ADDENDUM ADVANCED MODELS (HE150/HE250/HE300) G OR W 2 OR C AIR PROVING DEVICE 3 HumidiPRO C R U U S S OUTDOOR SENSOR 1 POWER IN LEFT LEFT 1 HE150/HE250 USES A 15 VA TRANSFORMER WIRED INTO 24V IN. HE100/HE200 USES A 10 VA TRANSFORMER WIRED INTO 24V IN. HE300 USES A LINE CORD PLUG. 2 CONNECT G TO HUMIDIFY WHEN THERE IS A FAN CALL. CONNECT W TO HUMIDIFY WHEN THERE IS A HEAT CALL. NEVER CONNECT BOTH. CONNECT C WHEN USING G OR W.
PAGE 2
WIRING CONFIGURATION 1 G (THERMOSTAT) HumidiPRO C R U U S S R G (FURNACE) 2 POWER IN OUTDOOR SENSOR RIGHT RIGHT 1 ONLY NEEDED IF SYSTEM’S THERMOSTAT DOES NOT ISOLATE Y FROM G. IF NEEDED, BREAK THE THERMOSTAT G TO SYSTEM G CONNECTION AND ROUTE THROUGH HUMIDIFIER AS SHOWN. 2 HE150/HE250 USES A 15 VA TRANSFORMER WIRED INTO 24V IN. HE100/HE200 USES A 10 VA TRANSFORMER WIRED INTO 24V IN. HE300 USES A LINE CORD PLUG. M35154 Fig. 3.
PAGE 3
WIRING CONFIGURATION BASIC MODELS (HE100/HE200) H8908 HUM/U WIRE HUM/U WIRE HUMIDIFIER OTHER WIRE(S) TO HVAC/FAN WHEN NECESSARY M24734 Fig. 5. Wiring connections on the H8908 humidistat. FAN CONTROL L1 (HOT) M35804 Fig. 6. Wiring H8908 humidistat. TRANSFORMER POWER SUPPLY 24V CONSTANT REQUIRED C R U U S S OUTDOOR SENSOR 2 L2 1 FURNACE FAN MOTOR HUMIDIFIER 1 PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. 2 24 VAC WIRING. M34570A Fig. 7.
PAGE 4
WIRING CONFIGURATION FAN CONTROL L1 (HOT) C R U U S S TRANSFORMER POWER SUPPLY 24V CONSTANT REQUIRED OUTDOOR SENSOR 2 L2 DPST SWITCHING RELAY 1 H L HUMIDIFIER 2-SPEED FAN MOTOR C 1 PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. 2 24 VAC WIRING. M34571A Fig. 8. Wiring HumidiPRO with 2-speed fan motor.