Instructions / Assembly
ASSEMBLY
POWERING THE LED
CLEANING
IMPORTANT SAFETY INSTRUCTIONS & POWER ON
FEATURES
ASSEMBLY
READ ALL INSTRUCTIONS
WARNING: Read all safety precautions and installation instructions carefully before installing or
servicing this fixture. Failure to comply with these instructions could result in a potentially fatal
electric shock, fire, and/or property damage.
•
When using outdoor portable work lights, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and personal injury.
• Use only a three-wire outdoor extension cord that has a three-prong grounding plug and
grounded receptacles that accept the light’s plug.
• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or
outlet(s) to be used for wet location. Receptacles are available having built-in GCFI
protection and are able to be used for this measure of safety.
• Use only with an extension cord for outdoor use, such as an extension cord of cord type:
SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW,
SJOW, SJOOW, SJTW, SJTOW or SJTOOW.
• Do not look directly at the LED Work Light when ON to avoid eye injury.
• Always keep the LED Work Light away from any flammable sources.
• Do not operate the LED Work Light if it has a missing or damaged lens cover.
• DO NOT SUBMERSE.
Save These Instructions
• Rugged Glass Lens
• Suitable for wet location use
• ETL Certified
• Energy Star rated
• Equipment has been tested and found to comply with the limits pursuant to Part 15, Subpart
B: 2012 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful electrical interference in a residential installation.
HARDWARE INCLUDED
TOOLS REQUIRED
A:
Round Head Screws (2)
M5x12 Hex Socket
B:
Round Head Screws (2)
M6x8 Hex Socket
C:
Metal Washers (2)
6.5 mm
L-Shaped Hex Wrench
4 mm
1. Attach Handle (1) to Lamp Head (2), lining up 2 holes on Handle to holes on Lamp Head.
2. Insert screws (A) through the holes.
3. Hand tighten with L-Shaped Hex Wrench (not included). Tighten the screws (A) until secure,
but avoid over tightening.
4. Attach Lamp Head (2) to “H” Base (3), lining up 2 holes on “U” Bracket to hole on “H” Base (3).
5. Place metal washers (C) on screws (B).
6. Insert screws (B) through the washers (C), “U” Bracket and the “H” Base (3).
7. Fit the screws (B) into the pre-threaded nuts in the “H” Base.
8. Hand tighten with L-Shaped Hex Wrench. Tighten the screws (B) until secure, but avoid over
tightening.
LAMP ANGLE ADJUSTMENT
1. Hold the LED Work Light by the ergonomic grip.
2. Holding the ergonomic grip, push forward or pull backward to adjust the LED Work Light.
3. Leave in desired position.
ON OFF
1. Plug the power cord to the 120Vac, 60 Hz outlet.
2. On the back of the LED Work Light, press the toggle switch to the ON position.
3. To turn off the LED Work Light, press the toggle switch to the OFF position.
WARNING: RISK OF ELECTRIC SHOCK - Do not use extension cord near water or where
water may accumulate. Keep light at least 16 feet from pools and spas. Keep plugs and
receptacles dry. For use only on GFCI protected circuits.
• Allow the LED Work Light to cool down before cleaning or storing.
• Clean LED Work Light Lens with a non-abrasive cleaner.
• Clean/Wipe down the handle and base with a damp cloth or non-abrasive cleaner.
USB CHARGING
3: “H” Base
B: M6x8 Hex Socket
Round Head Screws (2)
A: M5x12 Hex Socket
Round Head Screws (2)
1: Handle
2: Lamp Head
C: Metal Washers
6.5 mm (2)
“U” Bracket
• Unit is equiped with a 2A/5V USB charging port to
charge a portable electronic device.
• USB will charge device when plugged into outlet
regardless if unit is powered ON/OFF.
NOTE: Always put protective cap back over USB port
after use to protect from dirt or water.