Operation Manual
3
*Certain Models Only ** Certain models only, nozzles may vary according to model
All accessories can be tted to the end of the handle or the end of the telescopic tube.
Accessory Set* – Combines several functions in one, with maximum exibility by the
rotating body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be
stored neatly underneath the hose handle.
Crevice Tool* – For corners and hard to reach areas. [V1]
Furniture Nozzle* – For soft furniture and fabrics. [V2]
Dusting Brush* – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [V3]
Parquet Nozzle* – For parquet oors and other delicate oors. [Y]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [W]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas, particularly suitable for
allergen removal. [X]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
CLEANER MAINTENANCE
Replacing the Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch to open the bag door, pull the bag holder and pull the
pull the bag collar to remove the bag.
[11,12]
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust
bag should be disposed of correctly and carefully.
[13,14]
3. Fold a new bag as shown on the bag and t by inserting the collar into the bag holder.
4. Ret the bag holder and close the bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag holder are not
assembled to the cleaner. Always ensure the bag and bag holder are present when
closing the bag door.
REMEMBER: The bag check indicator LED* may also be lit if an obstruction has occurred.
In this case refer to ‘remove A Blockage From the System’.
Cleaning the Filters*
To maintain optimum performance of your cleaner, please wash the lters after each 5
bag changes.
1.
Lift the bag door release latch to open the bag door and remove the bag holder. [12]
2. Remove the pre-motor lter frame from the cleaner. [15]
3. Remove the lter sponge from the holder. [16]
4. Wash it in hand warm water, and allow it to dry thoroughly before replacing to the
cleaner. [19,20]
1.
To remove the exhaust sponge and the exhaust lter, remove the exhaust sponge
1 from the exhaust cover and unclip the lter pack and remove the other sponge 2.
[17,18,19]
2.
Wash them in hand warm water, and allow them to dry thoroughly before replacing.
[20,21]
REMEMBER: Do not use hot water or detergents. In the unlikely event of the lters
becoming damaged, t a Genuine Hoover replacement. Do not try and use the product
without a dust bag or lter tted.
Cleaning the permanent cloth dust bag*
To maintain optimum performance we recommended that you wash the permanent cloth
dust bag under warm water after every 5 full bags. Remove excess water and leave to
dry fully before replacing.
Removing a blockage from the system (*Certain model only)
If the bag check indicator LED is illuminated or ashing:
1.
Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.
2. If it is not full, then;
A. Do the lters need cleaning? If so refer to ‘Cleaning the Filter’.
B. Check if there is any other blockage in the system - Use a cord or a pole to
remove any blockage from the telescopic tube or exible hose.
WARNING - The bag check indicator LED will turn on if the cleaner is used when full, if
there is a blockage or if the lters are dirty. If the cleaner is used for a signicant period
of time with the bag check indicator LED is on, a thermal cut out will switch the cleaner
off to prevent overheating. The bag check indicator LED turns off once the cleaner has
switched off to signal that the thermal cut out has been activated. If this should happen,
switch the cleaner off, unplug and correct the fault. It will take about 30 minutes for the
cut out to automatically reset.
GB
USER CHECK LIST
Should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the dust bag over-lled? Please refer to ‘Cleaner Maintenance’.
• Is the Filter blocked? Please refer to ‘Cleaning the lter’.