Installation Guide

ManualsBrandsHouse of Hampton ManualsAll Ceiling Fans52'' Irven 5 - Blade Crystal Ceiling Fan with Pull Chain and Light Kit Included

You may install your ceiling fan as Flush Mount, using the Short or Long Rod. Measure your room height

before installing the fan and consider the different installation height options indicated in the above diagram.

INSTALL THE BULBS IN THE MOTOR HOUSING

before

hanging the ceiling fan

Required bulbs

(not included)

Light kit

use

–

E12, Type B, 40W x 2 (Not Included)

Motor housing

use

E12, Type C, 7W x 4 (Not Included)

Alternative bulbs usage: CFL or LED Bulbs may be used. Ensure the Max. Wattage indicated on the socket

labels is not exceeded, and verify the bulbs do not get in contact with any metal part of the fan components

(shade or motor housing)

Professional Installation Recommended

Note: Approximate time o

f assembly is 30 min to 1

hour

PRINTED IN CHINA

Table of Contents:

Safety tips Pg.2

Wiring Pg.7

Unpacking your fan Pg.

Blade Assembly Pg.9

Tools and material required Pg.4

Canopy Assembly Pg.9

Outlet Box Pg.5

Light Kit and Shade Assembly Pg.10

Hanging Bracket Installation Pg.4

Testing Your Fan Pg.11

Bulb installation Pg.6

Trouble Shooting Pg.11

Fan Assembly Pg.6

Maintenance Pg.12

READ AND SAVE THESE

INSTRUCTIONS

Installation Guide

PAGE 1

Summary of content (12 pages)

PAGE 1
Installation Guide READ AND SAVE THESE INSTRUCTIONS You may install your ceiling fan as Flush Mount, using the Short or Long Rod. Measure your room height before installing the fan and consider the different installation height options indicated in the above diagram.
PAGE 2
SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
PAGE 3
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or styrofoam to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory.
PAGE 4
3. Tools Required Step ladder Pliers Screw driver flat head and phillip Electrical tape Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft.(2.13m) from the floor and 30in.(76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling. Two down rods are included, 4” and 21” length.
PAGE 5
CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box. If installing on a vaulted ceiling, face opening of Hanging Bracket towards high point of ceiling.
PAGE 6
. Bulbs Installation. Installing bulbs in the Motor Housing, locate the four access plates on the motor housing top. Remove two screws per access plate to reach each socket, use phillip screwdriver. Do not remove the Center Screw on each Access Plate Install each candelabra base Type C, 7W bulbs (Not Included). Reattach the Access Plates ensuring the screws are tightened enough to avoid vibrations during the fan operation.
PAGE 7
8. Fan Assembly with Down Rod - Choose the 4” or 21” Down Rod Remove Pin and Clip from down rod (if you have not already done so). Slide the Down rod through the canopy, and the Down rod cover as shown. Thread the electrical wires through down rod and pull extra wire slack from the upper end of the down rod. Tip: Apply small piece of electrical tape to the ends of the electrical wires to keep them together when threading them through the down rod. Loosen the Yoke set screw.
PAGE 8
3.Install the receiver into the Hanging bracket of the fan. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. Do not install in damp locations or immerse in water. For indoor use only. Do not pull on or cut the receiver wire leads shorter. 4.Proceed making the wire connections following this diagram carefully. CAUTION: Incorrect wire connection would damage the receiver. Be sure outlet box is properly grounded or that a ground wire (GREEN or bare) is present.
PAGE 9
Important: Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring, or if the house/building wires are different colors than those referred to in the instructions, please use a qualified electrician. 10. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. Locate 15 blade attachment screws and washers in one of the hardware packs.
PAGE 10
11. Light Kit Assembly. 1. Remove the three screws from the Light kit. 2. Plug the connectors from the Light kit to the connectors from the Switch housing. Please note the correct wiring is:  White to White  Blue to Blue 3.Gently push the connectors into switch housing and align the holes in the Light kit with holes in the Switch housing. Secure the light kit with the 3 screws that were previously removed. Attach the Shade to the Light kit using the Finial you will find installed on the Light kit pipe.
PAGE 11
12. Testing Your Fan. It is recommended that you test the fan before finalizing installation. Restore power from circuit box and light switch (if applicable). Test the fan speeds from the Remote controller. Start at the OFF position (no blade movement) and continue testing the LOW, MED and HI speeds. Every time you press any key the red LED witness light will turn ON at the top of the controller. If the red LED witness light does not turn on when pressing any key, replace the 9 Volts battery.
PAGE 12
FAN FOUND NOISY 1. Always take a few days" break in" time for any new fan at medium or high speed. Try to diagnose the exact location of the noise by listening carefully from several sides (blades, motor, light kit, etc). Fan noise can come from a light kit. 2. Make sure all screws in the fan assembly and light kit are tight and properly threaded. If not, back out and re tighten. Tighten these screws at least twice a year because they may loosen slowly over time and cause clicking noise. 3.