HP 2012fc Modular Smart Array user guide Part number: 481597-002 First edition: January, 2013
Legal and notice information © Copyright 2008, 2013 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Document Conventions Rack Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Enclosures Into a Rack Preparing the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Rack Installation Overview and Procedure Attaching the Ear Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Connecting Controller and Drive Enclosures Connecting AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging in to SMU from a Local Management Host Updating Firmware . . . . . . . . . . . . . . . . . . . . . . . . 54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Configuring Host Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Creating Virtual Disks . . . . . . . . . . . . . .
HP 2012fc Modular Smart Array user guide • January 2013
About This Guide Intended Audience This guide is intended for use by system administrators and information professionals who are experienced with the following: ■ Direct attach storage (DAS) or storage area network (SAN) management ■ Network administration ■ Network installation ■ Storage system installation and configuration, including installing an HP rack Prerequisites Prerequisites for installing and configuring this product include familiarity with: ■ Servers and computer networks ■ Fibre Channel and
Document Conventions Typeface Meaning Examples AaBbCc123 Book title, new term, or emphasized word See the Release Notes. A virtual disk (vdisk) can .... You must be an advanced user to .... AaBbCc123 Directory or file name, value, command, or on-screen output The default file name is store.logs. The default IP address is 10.0.0.1. Type exit.
HP Technical Support Telephone numbers for worldwide technical support are listed on the HP support website: http://www.hp.com/support/. Collect the following information before calling: Technical support registration number (if applicable) ■ Product serial numbers ■ Product model names and numbers ■ Applicable error messages ■ Operating system type and revision level ■ Detailed, specific questions ■ For continuous quality improvement, calls may be recorded or monitored.
Subscription Service HP strongly recommends that customers sign up online using the Subscriber's choice website: http://www.hp.com/go/e-updates. Subscribing to this service provides you with e-mail updates on the latest product enhancements, newest versions of drivers, and firmware documentation updates as well as instant access to numerous other product resources. HP Websites For other product information, see the following HP websites: ■ ■ ■ ■ ■ http://www.hp.com http://www.hp.com/go/storage http://www.
CH A P T E R 1 Before You Begin The MSA2000 Family 2012fc Modular Smart Array and MSA2000 Drive Enclosure are high-performance storage solutions that combine outstanding performance with high reliability, availability, flexibility, and manageability. Supported configurations include a controller enclosure with or without attached drive enclosures. A controller enclosure can contain two controllers that interact and provide failover capability for the data path.
System Management Software Embedded management software includes a web-browser interface and the command-line interface described below. HP StorageWorks MSA2000 Family Storage Management Utility (SMU) SMU is the primary interface for configuring and managing the system. A web server resides in each controller module. SMU enables you to manage the system from a web browser that is properly configured and that can access a controller module through an Ethernet connection.
Hardware Components and LEDs This section describes the main hardware components of your storage system enclosures. Controller Enclosure Components and LEDs The controller enclosure can be connected to Fibre Channel host bus adapters (HBAs) or switches. Table 1-1 describes the controller enclosure components.
Figure 1-1 shows the LEDs on the front of a controller. Enclosure ID Drive module LEDs (top to bottom) Fault/UID Online/activity Status LEDs (top to bottom): UID Fault ID Heartbeat Drive modules are numbered by column top to bottom: 0–2, 3–5, 6–8, 9–11 Figure 1-1 Controller (Front View) Table 1-2 describes the LEDs on the front of a controller.
Table 1-3 describes the LEDs on the drive module. Table 1-3 Drive Module LED Combinations (Front) Online/Activity (green) Fault/UID (amber/blue) Description On Off The drive is online, but it is not currently active. Blinking irregularly Off The drive is active and operating normally. Off Amber, blinking regularly (1 Hz) Offline; the drive is not being accessed. A predictive failure alert has been received for this device. Further investigation is required.
Figure 1-2 shows the ports and switches at the back of the controller. Power switch LINK SPEED LINK SPEED FC Port 0 FC Port 1 LINK SPEED LINK SPEED FC Port 0 FC Port 1 Service DIRTY CLEAN CLI CACHE ACTIVITY DIRTY CLEAN Service port STATUS 10/100 BASE-T STATUS CLI CACHE ACTIVITY Host ports 10/100 BASE-T Service CLI port Ethernet port Expansion port Figure 1-2 Controller Ports and Switches (Back View) Table 1-4 describes the ports and switches on the back of the controller.
Figure 1-3 shows the LEDs at the back of the controller.
Table 1-5 Controller LEDs (Back) (Continued) Location Controller module Controller module Controller module Controller module Controller module Controller module Controller module 18 LED Unit Locator OK to Remove Fault/Service Required OK Cache status Host activity Ethernet link status Color State Description White Off Normal operation. Blink Physically identifies the controller module. Off The controller module is not prepared for removal.
Table 1-5 Controller LEDs (Back) (Continued) Location LED Color State Description Controller module Ethernet activity Green Off The Ethernet link has no I/O activity. Blink The Ethernet link has I/O activity. Off The port is empty or the link is down. On The port link is up and connected.
Figure 1-4 shows the ports and switches at the back of the drive enclosure. Power switch 0 0 Service 0 0 Service SAS In port Service port SAS Out port Figure 1-4 Drive Enclosure Ports and Switches (Back View) Table 1-7 describes the ports and switches on the back of the drive enclosure.
Figure 1-5 shows the LEDs at the back of the drive enclosure. AC Power Good DC Voltage/Fan Fault/ Service Required SAS In port status 0 SAS Out port status 0 Service 0 0 Service Unit Locator OK OK to Remove Fault/Service Required Figure 1-5 Drive Enclosure LEDs (Back View) Table 1-8 describes the LEDs on the back of the drive enclosure.
Table 1-8 Drive Enclosure LEDs (Back) (Continued) Location Expansion module Expansion module Expansion module 22 LED Fault/Service Required OK SAS Out port status Color State Description Amber On A fault has been detected or a service action is required. Blink Indicates a hardware-controlled power up or a cache flush or restore error. Off Expansion module is not OK. On Expansion module is operating normally. Blink System is booting. Off The port is empty or the link is down.
Installation Checklist Table 1-9 outlines the steps required to install the enclosures and initially configure the system. To ensure a successful installation, perform the tasks in the order they are presented. Table 1-9 Installation Checklist Step Installation Task Where to Find Procedure 1. Prepare the rack for installation. “Preparing the Rack” on page 27 2. Install the controller enclosure and optional drive enclosures in the rack. “Rack Installation Overview and Procedure” on page 28 3.
HP 2012fc Modular Smart Array user guide • January 2013
CH A P T E R 2 Installing and Cabling Enclosures This chapter describes how to install and cable enclosures in a standard 19-inch EIA rack cabinet.
Safety Precautions For your protection, observe the following safety precautions when setting up your equipment: ■ Follow all cautions and instructions marked on the equipment. ■ Ensure that the voltage and frequency of your power source match the voltage and frequency inscribed on the equipment’s electrical rating label. ■ Never push objects of any kind through openings in the equipment. Dangerous voltages may be present.
Installing Enclosures Into a Rack This section describes how to install the enclosures into a standard 19-inch rack cabinet with a 28 to 36-inch (71.12 to 91.44-cm) depth. Tip – Keep all hardware items in plastic bags until you are ready to use them. This enables you to correctly identify the screws and avoid confusion.
Rack Installation Overview and Procedure Figure 2-1 provides a visual overview of rack installation and components and corresponds to the steps that follow. #10-32 x 5/8-in. Truss screws (Step 6) #10-32 x 5/8-in. Truss screws (Step 9) Rear bracket connected to rack Threaded PEMs (4) Side bracket #8-32 x 3/16-in. flathead screws (Step 5) #8-32 x 1/4-in.
Use the following procedure and refer to Figure 2-1 to install each enclosure into the rack. When positioning an enclosure in the rack, do not block the air vents at the front or back of the enclosure. Caution – If you only have one person to perform the installation, remove the power and cooling modules and drive modules from an enclosure before installation, and use the optional nylon front support brackets.
Figure 2-2 Side Bracket With Alignment Marks b. On one side, insert the first two screws through the side bracket slots above and below the alignment mark into the rear-most threaded holes in the enclosure. For example, to mount the enclosure in a 28-inch deep rack, position the side bracket so that the 28-inch alignment mark is aligned with the rear-most threaded holes in the enclosure. c.
Attaching the Ear Caps The plastic ear caps are snap-on parts that require some care when attaching or removing them. After the enclosure has been installed in the rack cabinet, attach the ear caps, which are located in a plastic bag included in the controller enclosure package. 1. Remove the ear caps from the plastic package. 2. As you attach each ear cap, hold it so that its indent is closest to the chassis. Indent Left ear cap Indent Right ear cap Figure 2-3 Ear Caps 3.
Connecting Controller and Drive Enclosures Use the supplied SAS cables to connect a controller enclosure to up to three drive enclosures. Figure 2-4 and Figure 2-5 show the recommended fault-tolerant cabling patterns. In an enclosure, the upper module is designated A and the lower module is designated B. When connecting multiple drive enclosures, use reverse cabling to ensure the highest level of fault tolerance.
Controller A Controller B 1A In Out In Out In Out 2A In Out 2B In Out 3A In Out 3B 1B Figure 2-5 Fault-Tolerant Cabling Connections Between One Controller Enclosure and Up to Three Drive Enclosures Chapter 2 Installing and Cabling Enclosures 33
Controller A Controller B In Out 1A In Out 1B In Out 2A In Out 2B In Out In Out 3A 3B Figure 2-6 Non-Fault-Tolerant Cabling Connections Between One Controller and Up to Three Drive Enclosures 34 HP 2012fc Modular Smart Array user guide • January 2013
Connecting AC Power Use this procedure to connect AC power to the enclosures. 1. Verify that both power switches are off. 2. Using the AC power cords, for each enclosure, connect one power and cooling module to one power source in the rack, and the other power and cooling module to a separate power source in the rack. 3. Connect the primary power cords from the rack to separate external power sources. Power on the system as described in the topic that follows.
Testing the Enclosure Connections Use this procedure to power on the newly installed system. 1. Press the power switches at the back of each drive enclosure to the On (–) position. This ensures that the disks in the enclosures have enough time to completely spin up before being scanned by the RAID modules in the controller enclosure. Depending on your configuration, it can take several minutes for the system to power up. While enclosures power up, their LEDs blink.
Correcting Enclosure IDs When installing a system with drive enclosures attached, the enclosure IDs might not agree with the physical cabling order. This is because the controller might have been previously attached to some of the same enclosures and it attempts to preserve the previous enclosure IDs if possible. To correct this condition, make sure that both controllers are up and perform a rescan using SMU or the CLI.
HP 2012fc Modular Smart Array user guide • January 2013
CH A P T E R 3 Connecting Hosts This chapter describes how to connect data and management hosts to controller enclosures.
Installing the MSA2000 Family SES Driver for Microsoft Windows Hosts Installing the MSA2000 Family SCSI Enclosure Services (SES) driver prevents Microsoft Windows hosts from displaying the Found New Hardware Wizard when the storage system is discovered. 1. Download MSA2000 Family SCSI Enclosure Services (SES) driver package msa2000-ses-version.zip from the http://www.hp.com/go/msa. Select MSA SAN Arrays, select your product, and go to Related products. 2.
Using Host Port Interconnects When the internal connections between host ports are enabled through SMU, host port 0 on each controller is internally connected to host port 1 on the other controller. This provides redundancy in the event one controller fails (failover) by making volumes owned by the failed controller accessible on the surviving controller.
Connecting Direct Attach Configurations This section explains how to connect the controller enclosure directly to data hosts. It shows configurations that support high availability and high performance, and notes when host port interconnects must be enabled. The controller enclosure has four host connections, two per controller. Connect FC cables from host ports on each controller to FC HBAs on data hosts, as shown in the following figures.
Figure 3-2 shows a non-redundant configuration that can be used when high performance is more important than high availability. This configuration requires host port interconnects to be disabled, which they are by default.
Connecting Switch Attach Configurations This section explains how to connect the controller enclosure to data hosts through one or more external FC switches. The controller enclosure has four host connections, two per controller. Connect FC cables from controller hosts ports to switch ports, and from switch ports to data hosts, as shown in the following figures. To maintain redundancy, connect each data host through the switch or switches to both controller A and controller B.
Connecting One Data Host Through One Switch Figure 3-3 shows a dual-controller connection through one switch to one dual-port data host with two FC HBA ports. This configuration requires that host port interconnects are disabled, which they are by default. It also requires host-based multipathing software.
Connecting Two Data Hosts Through Two Switches Figure 3-4 shows the preferred high-availability dual-controller connection through two switches to two dual-port data hosts, in which each data host has two FC HBA ports with each port connected to a different switch. This configuration requires that host port interconnects are disabled, which they are by default.
Connecting Two Data Hosts Through a Zoned Switch Figure 3-5 shows a high-availability, dual-controller connection through a two-zone switch. Each zone can be an independent switch (see Figure 3-4). Zone 0 Zone 1 Controller A Controller B Figure 3-5 High-Availability Dual-Controller Connection Through a Two-Zone Switch to Two Dual-Port Data Hosts Connecting Remote Management Hosts The management host directly manages systems out-of-band over an Ethernet network.
HP 2012fc Modular Smart Array user guide • January 2013
CH A P T E R 4 Configuring a System for the First Time This chapter describes how to perform first-time configuration on the storage system. It also describes how to perform basic storage configuration to verify that your system is working.
Setting Management Port IP Addresses Using the CLI Note – If you used DHCP to set the IP addresses, you do not have to set them using the CLI as described in this section. Ethernet Management ports on controller module A and controller module B are configured with the following default values: ■ Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B) ■ IP Subnet Mask: 255.255.255.0 ■ Gateway IP Address: 10.0.0.
Your package contents include a micro-DB9-to-DB9 serial cable. If necessary, use a DB9-to-DB25 adapter (not included) for connecting the serial cable to a DB25 serial port on the host computer. 3. Start and configure a terminal emulator, such as HyperTerminal or VT-100, using the display settings in Table 4-1 and the connection settings in Table 4-2.
4. In the terminal emulator, connect to controller A. 5. Press Enter to display the CLI prompt (#). 6.
9. In the host computer's command window, type the following command to verify Ethernet connectivity, first for controller A and then for controller B: ping IP-address If you cannot your access your system for at least three minutes after changing the IP address, your network might require you to restart the management controller using the serial CLI. When you restart a management controller, communication with it is temporarily lost until it successfully restarts.
Logging in to SMU from a Local Management Host To log in to SMU from a local management host: 1. In your web browser’s address field, type the IP address of one of the controller enclosure’s Ethernet management ports and press Enter. The SMU Login page is displayed. If the Login page does not display, verify that you have entered the correct IP address. 2. On the login page, type the default management user name manage and default password !manage. 3. Click Log In. The Status Summary page is displayed.
■ If a time server can provide local time rather than UT, configure the storage devices to use that time server, with no further time adjustment. If no NTP server is present, the date and time are maintained as if NTP had not been enabled. To manually set the system date and time: 1. Select Manage > General Config > Set Date/Time. 2. In the Set System Date panel, select the current month, day, and year. 3. In the Set System Time panel, type time values using a 24-hour clock (where hour 8 represents 8 a.m.
2. In the Controller Module Host Port Configuration panels, for each port to which an HBA or switch is attached, set the appropriate link speed. An FC port’s link speed must match the speed of the FC HBA or switch to which the port is connected. In a dual-controller system, if FC port interconnects are enabled, changing the speed of a port on one controller also changes the speed of the interconnected port on the other controller. 3. Click Update Host Port Configuration. 4.
Creating Virtual Disks Two or more disk drives can be logically combined to form a virtual disk. The combined storage capacity can then be partitioned into volumes. SMU provides both manual and automatic methods for creating virtual disks, as described in its online help and in the reference guide.
Mapping a Data Host to a Volume To enable a data host to access a volume you created, you must map the volume to the host. The port World Wide Name (WWN) of each host connected to the system is automatically added to the system’s global host port list. Before mapping a data host to a volume you must identify the data host’s port WWN and a LUN that the host is not using. To map a data host to a volume: 1. Select Manage > Volume Management > Volume Mapping > Map Hosts To Volume.
Testing the Configuration To determine that your system is ready for use, test the configuration as follows: 1. In SMU, select Monitor > Vdisk Status and view the configuration information for each virtual disk. The virtual disk status is Critical during initialization but you can perform I/O to the volume. 2. From the data host: a. Make the volume an operating system partition. b. Verify that you can access the mapped volume and the volume size shown on the data host matches the size shown in SMU. c.
HP 2012fc Modular Smart Array user guide • January 2013
APPENDIX A Powering the System Off and On This appendix describes how to power off and power on the system when needed. Powering Off the System The system rarely needs to be powered off. You remove power only when you plan to physically move the system to another location. Use this procedure when you need to power off the system. 1. Stop all I/O from hosts to the system. 2. Use SMU to shut down both controllers. Wait until SMU indicates that processing is complete. 3.
2. Press the power switches at the back of the controller enclosure to the On (–) position. If the enclosure’s power-on sequence succeeds as described in Step 1, the system is ready to use.
APPENDIX B Regulatory Compliance and Safety Regulatory Compliance Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interferencefree radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
To identify this product, refer to the part, Regulatory Model Number, or product number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.
Laser Safety Warning Warning – To reduce the risk of exposure to hazardous radiation: ■ ■ ■ Do not try to open the laser device enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP authorized service technicians to repair the laser device.
International Notices and Statements Canadian Notice (avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
■ Also approved under UL 60950/CSA C22.2 No. 60950-00, Safety of Information Technology Equipment.
Korean Notices Safety Battery Replacement Notice Your computer is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product.
Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP Partner, or their agents. For more information about battery replacement or proper disposal, contact an HP authorized reseller or service provider.
Japanese Power Cord Notice Electrostatic Discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Note – For more information on static electricity, or assistance with product installation, contact your HP authorized reseller. Waste Electrical and Electronic Equipment Directive Czechoslovakian Notice Danish Notice Bortskaffelse af affald fra husstande i den Europæiske Union Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må bortskaffes med andet almindeligt husholdningsaffald.
Dutch Notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.
Estonian Notice Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti.
French Notice Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques.
Greek Notice . , . . , , . Hungarian Notice Készülékek magánháztartásban történ selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltér módon kezelend . A vásárló a hulladékká vált készüléket köteles a kijelölt gy jt helyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Italian Notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.
Lihuanian Notice Nolietotu iek rtu izn cin šanas noteikumi lietot jiem Eiropas Savien bas priv taj s m jsaimniec b s Š ds simbols uz izstr d juma vai uz t iesai ojuma nor da, ka šo izstr d jumu nedr kst izmest kop ar citiem sadz ves atkritumiem. J s atbildat par to, lai nolietot s iek rtas tiktu nodotas speci li iek rtotos punktos, kas paredz ti izmantoto elektrisko un elektronisko iek rtu sav kšanai otrreiz jai p rstr dei.
Portuguese Notice Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.
Slovenian Notice Spanish Notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos.
Swedish Notice Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
HP 2012fc Modular Smart Array user guide • January 2013
Index A accessing SMU, 54 the CLI, 50 accumulators, 70 Avis Canadien, regulatory compliance notice, 67 B batteries recycling or disposal, 70 replacement notice, 69 Taiwan EPA recycling and disposal, 70 boot straps, using, 71 BSMI, regulatory compliance notice, 68 C cables FCC compliance statement, 65 shielded, 65 Canada, regulatory compliance notice, 67 certification and classification information, laser, 66 Class A equipment, Canadian compliance statement, 67 Class B equipment, Canadian compliance statem
cord.
I IEC EMC, worldwide regulatory compliance notice, 67 indicators, See LEDs installing enclosures checklist, 23 in a rack, 28 safety precautions, 26 installing required host software and drivers SES driver, 40 interconnects, enabling, 41 IP addresses setting using DHCP, 36 setting using the CLI, 50 J Japan regulatory compliance notice, 68 K Korean, regulatory compliance notice, 69 L label, laser, 66 laser international certification and classification information, 66 product label, 66 radiation, warning,
preparing, 27 recycling, battery, 70 recycling, Taiwan EPA battery, 70 regulatory compliance information number, 65 notices BSMI, 68 Canada, 67 Class A, 63 Class B, 64 European Union, 67 HP series number, 65 IEC EMC statement, worldwide, 67 Japan, 68 Korean, 69 lasers, 65 modifications, 65 shielded cables, 65 remote management, 47 replacing a power cord, 70 reverse cabling, 32 RFI/EMI connector hoods, 65 storage website, 10 straps, ground boot, 71 heel, 71 toe, 71 Subscriber’s choice website, 10 Subscriber
using, 71 Index 87
HP 2012fc Modular Smart Array user guide • January 2013
